Package Characteristics
Parameter
Sym.
Input-Output
V
ISO
Momentary
Withstand
Voltage**
Resistance
R
I-O
(Input-Output)
Capacitance
C
I-O
(Input-Output)
Input-Input
I
I-I
Insulation
Leakage Current
Input-Input
R
I-I
Insulation
Leakage Current
Capacitance
C
I-I
(Input-Input)
Device HCPL- Min.
2500
Typ.* Max.
Units
V rms
Test Conditions
RH
≤
50%,
t = 1 min.,
T
A
= 25˚C
V
I-O
= 500 Vdc
RH
≤
45%
f = 1 MHz
RH
≤
45%
V
I-I
= 500 Vdc
Fig.
Note
4, 9
10
12
0.6
0.005
Ω
pF
µA
Ω
4
11
5
10
11
5
2730
2731
0730
0731
0.03
0.25
pF
5
*All typical values at T
A
= 25˚C, unless otherwise noted.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your equipment level
safety specification or Agilent Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
1. Pin 5 should be the most negative voltage at the detector side.
2. Each channel.
3. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I
O
, to the forward LED input current, I
F
, times 100%.
4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
6. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
CM
/dt of the common mode pulse, V
CM
, to
assure that the output will remain in a Logic High state (i.e., V
O
> 2.0 V). Common mode transient immunity in a Logic Low level is the
maximum tolerable (negative) dV
CM
/dt of the common mode pulse, V
CM
, to assure that the output will remain in a Logic Low state
(i.e., V
O
< 0.8 V).
7. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, R
CC
, should be included to protect the
detector IC from destructively high surge currents. The recommended value is R
CC
= 110
Ω.
8. Use of a 0.1
µF
bypass capacitor connected between pins 5 and 8 adjacent to the device is recommended.
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 3000 V rms for 1 second (leakage
detection current limit, I
I-O
< 5
µA).
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage
detection current limit, I
I-O
< 5
µA).
11. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
12. Derate linearly above 65˚C free-air temperature at a rate of 2.3 mW/˚C for the SO-8 package.
9
AGILENT [ AGILENT TECHNOLOGIES, LTD. ]
