PWM
Carrier waveform
Source
Internal modulation Sine, Square, Ramp, Triangle, Noise, Arb
(2 mHz to 20 kHz)
Deviation
FSK
Carrier waveforms
Source
Internal modulation 50% duty cycle square (2 mHz to 100 kHz)
External Modulation Input[6] (for AM, FM, PM, PWM)
Voltage range
Input impedance
Bandwidth
PROGRAMMING TIMES (typical)
Pulse
Internal/External
Configuration times
USB
LAN
GPIB
111 ms
1.2 ms
30 ms
Function Change
Frequency Change
Amplitude Change
Select User Arb
111 ms
1.5 ms
30 ms
111 ms
2.7 ms
30 ms
124 ms
0% to 100% of pulse width
124 ms
123 ms
Sine, Square, Ramp, Arb
Internal/External
Arb Download Times (binary transfer)
USB
LAN
GPIB
64K points
16K points
4K points
96.9 ms
24.5 ms
7.3 ms
191.7 ms
48.4 ms
14.6 ms
336.5 ms
80.7 ms
19.8 ms
5 V full scale
5 kΩ typical
DC to 20 kHz
GENERAL
Power Supply
CAT II
SWEEP
100 - 240V @ 50/60Hz (-5%, +10%)
100 - 120V @ 400Hz ( 10%)
50 VA max
Waveforms
Type
Direction
Sweep time
Trigger
Sine, Square, Ramp, Arb
Linear or Logarithmic
Up or Down
1 ms to 500 s
Single, External, or Internal
Power Consumption
Operating Environment IEC 61010
Pollution Degree 2
Indoor Location
Operating Temperature 0°C to 55°C
Operating Humidity
Operating Altitude
Marker
falling edge of sync signal
(programmable frequency)
5% to 80% RH, non-condensing
Up to 3000 meters
Storage Temperature
State Storage Memory
-30°C to 70°C
Power off state automatically saved.
Four user-configurable stored states
USB, GPIB, and LAN standard
SCPI - 1993, IEEE-488.2
BURST[7]
Waveforms
Type
Start/Stop Phase
Internal Period
Gate Source
Trigger source
Sine, Square, Ramp, Triangle, Pulse, Noise, Arb
Counted (1 to 50,000 cycles), Infinite, Gated
-360° to +360°
1 µs to 500 s
External trigger
Interface
Language
Dimensions (W x H x D)
Bench top
Rack mount
Weight
261.1mm x 103.8mm x 303.2mm
212.8mm x 88.3mm x 272.3mm
3.4 kg (7.5 lbs)
Single, External or Internal
Safety Designed to
EMC Tested to
Vibration and Shock
Acoustic Noise
Warm-up Time
Warranty
UL-1244, CSA 1010, EN61010
MIL-461C, EN55011, EN50082-1
MIL-T-28800, Type III, Class 5
30 dBa
1 hour
1 year
TRIGGER CHARACTERISTICS
Trigger input
Input level
Slope
Pulse width
Input impedance
Latency
TTL compatible
Rising or Falling, selectable
> 100 ns
>10 kΩ, DC coupled
< 500 ns
Jitter (rms)
Trigger output
Level
Pulse width
Output Impedance 50 Ω, typical
6 ns (3.5 ns for pulse)
TTL compatible into ≥ 1 kΩ
> 400 ns
Footnotes
[1]
add 1/10th of output amplitude and offset spec per °C for operation
outside the range of of 18°C to 28°C
Maximum rate
Fanout
1 MHz
≤ 4 Agilent 33220As
[2]
[3]
[4]
[5]
[6]
[7]
Autorange enabled
DC offset set to 0 V
spurious output at low amplitude is –75 dBm typical
add 1 ppm/°C average for operation outside the range of 18°C to 28°C
FSK uses trigger input (1 MHz maximum)
Sine and square waveforms above 6 MHz are allowed only with
an “infinite” burst count
3