欢迎访问ic37.com |
会员登录 免费注册
发布采购

CA16B2CNN 参数 Datasheet PDF下载

CA16B2CNN图片预览
型号: CA16B2CNN
PDF下载: 下载PDF文件 查看货源
内容描述: CA16型2.5 Gb / s的DWDM转发器,具有16通道155 Mb / s的复用器/解复用器 [CA16-Type 2.5 Gbits/s DWDM Transponder with 16-Channel 155 Mbits/s Multiplexer/Demultiplexer]
分类和应用: 解复用器
文件页数/大小: 30 页 / 442 K
品牌: AGERE [ AGERE SYSTEMS ]
 浏览型号CA16B2CNN的Datasheet PDF文件第9页浏览型号CA16B2CNN的Datasheet PDF文件第10页浏览型号CA16B2CNN的Datasheet PDF文件第11页浏览型号CA16B2CNN的Datasheet PDF文件第12页浏览型号CA16B2CNN的Datasheet PDF文件第14页浏览型号CA16B2CNN的Datasheet PDF文件第15页浏览型号CA16B2CNN的Datasheet PDF文件第16页浏览型号CA16B2CNN的Datasheet PDF文件第17页  
Advance Data Sheet  
March 2001  
CA16-Type 2.5 Gbits/s DWDM Transponder with  
16-Channel 155 Mbits/s Multiplexer/Demultiplexer  
Functional Description (continued)  
Transponder Interfacing  
The TxD[0:15]P/N, TxREFCLKP/N, and PICLKP/N  
inputs and the RxQ[0:15]P/N, POCLKP/N, and PCLKP/  
N outputs are high-speed (155 Mbits/s),LVPECL differ-  
ential data and clock signals.To maintain optimum sig-  
nal fidelity, these inputs and outputs must be  
Loopback Modes  
The CA16-type transponder is capable of operating in  
either of two loopback modes: diagnostic loopback or  
line loopback.  
connected to their terminating devices via 50 ¾ con-  
trolled-impedance transmission lines. The transmitter  
inputs (TxD[0:15]P/N, TxREFCLKP/N, and PICLKP/N)  
must be terminated as close as possible to the CA16  
transponder connector with a Thevenin equivalent  
impedance equal to 50 terminated to Vcc – 2 V. The  
receiver outputs (RxQ[0:15]P/N, POCLKP/N, and  
PCLKP/N) must be terminated as close as possible to  
the device (IC) that these signals interface to with a  
Thevenin equivalent impedance equal to 50 termi-  
nated to Vcc – 2 V.  
Line Loopback  
When LLOOP is pulled low, the received serial data  
stream and recovered 2488.32 MHz serial clock from  
the optical receiver are connected directly to the serial  
data and clock inputs of the optical transmitter. This  
establishes a receive-to-transmit loopback at the serial  
line rate.  
Diagnostic Loopback  
When DLOOP is pulled low, a loopback path is estab-  
lished from the transmitter to the receiver. In this mode,  
the serial data from the parallel-to-serial converter and  
the transmit serial clock is looped back to the serial-to-  
parallel converter and the frame and byte detect cir-  
cuitry, respectively.  
Figure 3, below, shows one example of the proper ter-  
minations. Other methods may be used, provided they  
meet the requirements stated above.  
3.3 V  
SONET/SDH  
INTERFACE IC  
CA16-TYPE TRANSPONDER  
130 Ω  
80 Ω  
130 Ω  
80 Ω  
TxD[0:15]P  
(LVPECL)  
50 IMPEDANCE  
TRANSMISSION LINES  
TxLINE  
MUX  
Tx  
TxD[0:15]N  
(LVPECL)  
3.3 V  
130 Ω  
80 Ω  
130 Ω  
80 Ω  
RxD[0:15]P  
(LVPECL)  
50 IMPEDANCE  
TRANSMISSION LINES  
RxLINE  
DEMUX  
Rx  
RxD[0:15]N  
(LVPECL)  
1-1054(F)  
Figure 3. Transponder Interfacing  
13  
Agere Systems Inc.