欢迎访问ic37.com |
会员登录 免费注册
发布采购

ACT4438 参数 Datasheet PDF下载

ACT4438图片预览
型号: ACT4438
PDF下载: 下载PDF文件 查看货源
内容描述: ACT4438-1收发器符合MIL -STD-一千七百六十〇分之一千五百五十三在一个芯片级封装 [ACT4438-1 Transceiver for MIL-STD-1553 / 1760 in a Chipscale Package]
分类和应用:
文件页数/大小: 7 页 / 152 K
品牌: AEROFLEX [ AEROFLEX CIRCUIT TECHNOLOGY ]
 浏览型号ACT4438的Datasheet PDF文件第2页浏览型号ACT4438的Datasheet PDF文件第3页浏览型号ACT4438的Datasheet PDF文件第4页浏览型号ACT4438的Datasheet PDF文件第5页浏览型号ACT4438的Datasheet PDF文件第6页浏览型号ACT4438的Datasheet PDF文件第7页  
ACT4438–1
Transceiver for MIL-STD-1553 / 1760
in a Chipscale Package
Preliminary
Features
• Transceiver meets military data bus requirements,
MIL-STD-1553 and MIL-STD-1760
• Low power dissipation at full output power
• Single +5V power supply
• Current Source Transmitter Output
• Bipolar Monolithic Construction
• Miniature Chipscale Package Bumped Chip Carrier
(BCC++)
CIRCUIT TECHNOLOGY
www.aeroflex.com
General Description
The Aeroflex Circuit Technology
Model ACT4438-1 is a next
generation
monolithic transceiver
which provide full compliance with
MIL-STD-1553/1760 and data bus
requirements in a Bumped Chip
Carrier™ (BCC++) with the lowest
standby power consumption and
single power supply operation.
The Model ACT4438-1 performs the
front-end analog function of inputting
and outputting data through a
transformer to a MIL-STD-1553/1760
data bus with a few external
components.
Design of these transceivers reflects
particular attention to active filter
performance. This results in low bit
and word error rate with superior
waveform purity and minimal zero
crossover
distortion.
Efficient
transmitter electrical and thermal
design provides low internal power
dissipation and heat rise at high as
well as low duty cycles.
Shown 2X
NOTE: BCC++ and Bumped Chip Carrier are Trademarks of Fujitsu Ltd.
Block Diagram (without Transformer)
Transmitter
The Transmitter section accepts
bi-phase TTL data at the input and
when coupled to the data bus with a
1:2.5 transformer, isolated on the
data bus side with two 55 Ohm fault
isolation resistors for direct stub
coupling. The data bus signal
produced for RISET = 2.7K Ohm is
typically 7.5 Volts nominal P-P at
A-A’, See Figure 5. When both DATA
and DATA inputs are held low, the
transmitter output becomes a high
impedance and is “removed” from the
line. In addition, an overriding
“INHIBIT" input provides for the
removal of the transmitter output from
the line. A logic “1” applied to the
“INHIBIT” takes priority over the
TX DATA OUT
TX DATA IN
TX DATA IN
DRIVER
SHAPING
OUTPUT
STAGE
TX DATA OUT
TX INHIBIT
RISET
+5 V
GROUND
REFERENCE
COMP.
RX DATA OUT
RX DATA IN
RX DATA IN
INPUT
AMP
ACTIVE
FILTER
COMP.
RX DATA OUT
STROBE
eroflex Circuit T
echnology
– Data Bus Modules For The Future © SCD4438-1 REV A 11/19/01