ADG406/ADG407/ADG426
SINGLE SUPPLY
VDD = +12 V 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 2.
Parameter1
+25°C −40°C to +85°C Unit
Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range
RON
0 to VDD
200
V
90
125
Ω typ
Ω max
VD = +3 V, +8.5 V, IS = −1 mA;
VDD = +10.8 V
LEAKAGE CURRENTS
Source Off Leakage IS (Off)
Drain Off Leakage ID (Off)
ADG406, ADG426
ADG407
VDD = +13.2 V
nA max VD = 8 V/0.1 V, VS = 0.1 V/8 V; see Figure 26
0.5
20
VD = 8 V/0.1 V, VS = 0.1 V/8 V; see Figure 27
1
1
20
20
nA max
nA max
Channel On Leakage ID, IS (On)
ADG406, ADG426
ADG407
VS = VD = 8 V/0.1 V, see Figure 28
1
1
20
20
nA max
nA max
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
2.4
0.8
V min
V max
IINL or IINH
1
ꢀA max VIN = 0 or VDD
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS2
tTRANSITION
8
pF typ
f = 1 MHz
180
220
10
180
240
135
180
ns typ
ns max
ns typ
ns typ
ns max
ns typ
ns max
RL = 300 Ω, CL = 35 pF; V1 = 8 V/0 V, V2 = 0 V/8 V; see Figure 29
350
Break Before Make Delay, tOPEN
tON (EN, WR)
RL = 300 Ω, CL = 35 pF; VS = 5 V, see Figure 30
RL = 300 Ω, CL = 35 pF;
350
220
VS = +5 V, see Figure 31
RL = 300 Ω, CL = 35 pF; VS = 5 V, see Figure 31
tOFF (EN, RS)
ADG426 Only
tW, Write Pulse Width
tS, Address, Enable Setup Time
tH, Address, Enable Hold Time
tRS, Reset Pulse Width
Charge Injection
Off Isolation
100
100
10
ns min
ns min
ns min
ns min
pC typ
dB typ
dB typ
pF typ
100
VS = +5 V
5
VS = 6 V, RS = 0 Ω, CL = 1 nF; see Figure 34
RL = 1 kΩ, f = 100 kHz; see Figure 35
RL = 1 kΩ, f = 100 kHz; see Figure 36
f = 1 MHz
−75
85
8
Channel-to-Channel Crosstalk
CS (Off)
CD (Off)
f = 1 MHz
ADG406, ADG426
ADG407
80
40
pF typ
pF typ
f = 1 MHz
CD, CS (On)
ADG406, ADG426
ADG407
100
50
pF typ
pF typ
POWER REQUIREMENTS
IDD
VDD = +13.2 V
VIN = 0 V, VEN = 0 V
1
5
ꢀA typ
ꢀA max
ꢀA typ
ꢀA max
IDD
100
200
VIN = 0 V, VEN = 2.4 V
500
1 Temperature range is −40°C to +85°C.
2 Guaranteed by design, not subject to production test.
Rev. B | Page 6 of 20
ADI [ ADI ]
