AD8362
SPECIFICATIONS
V
S
= 5 V, T = 25°C, Z
O
= 50 Ω, differential input drive via balun
, VTGT connected to VREF, VOUT tied to VSET, unless otherwise noted.
Table 1.
Parameter
OVERALL FUNCTION
Maximum Input Frequency
Input Power Range (Differential)
Nominal Low End of Range
Nominal High End of Range
Input Voltage Range (Differential)
Nominal Low End of Range
Nominal High End of Range
Input Power Range (S-Sided)
Nominal Low End of Range
Nominal High End of Range
Input Voltage Range (S-Sided)
Nominal Low End of Range
Nominal High End of Range
Input Power Range (S-Sided)
Nominal Low End of Range
Nominal High End of Range
Output Voltage Range
Nominal Low End of Range
Nominal High End of Range
Output Scaling (Log Slope)
Law Conformance Error
RF INPUT INTERFACE
Input Resistance
OUTPUT INTERFACE
Available Output Range
Absolute Voltage Range
Nominal Low End of Range
Nominal High End of Range
Source/Sink Current
Slew Rate Rising
Slew Rate Falling
Rise Time, 10% to 90%
Fall Time, 90% to 10%
Wideband Noise
VSET INTERFACE
Nominal Input Voltage Range
Input Resistance
Scaling (Log Slope)
Scaling (Log Intercept)
VOLTAGE REFERENCE
Output Voltage
Temperature Sensitivity
Output Resistance
Conditions
Min
Typ
3.8
dB referred to 50 Ω impedance level, f ≤ 2.7 GHz, into 1:4 balun
Max
Unit
GHz
dBm
dBm
mV rms
V rms
dBm
dBm
mV rms
V rms
dBm
dBm
mV
V
mV/dB
dB
Ω
Ω
−52
8
RMS voltage at input terminals, f ≤ 2.7 GHz, into input of the device
1.12
1.12
Single-ended drive, CW input, f ≤ 2.7 GHz, into input resistive network
−40
0
RMS voltage at input terminals, f ≤ 2.7 GHz
2.23
2.23
Single-ended drive, CW input, f ≥ 2.7 GHz, into matched input network
−35
12
R
L
≥ 200 Ω to ground
In general, V
S
− 0.1 V
Over central 60 dB range, f ≤ 2.7 GHz
Pin INHI, Pin INLO, ac-coupled, at low frequencies
Single-ended drive, with respect to DECL
Differential drive
Pin VOUT
R
L
≥ 200 Ω to ground
Measurement mode, f = 900 MHz, P
IN
= −52 dBm
Measurement mode, f = 900 MHz, P
IN
= +8 dBm
VOUT held at V
S
/2, to 1% change
C
L
= open
C
L
= open
0.2 V to 1.8 V, CLPF = Open
1.8 V to 0.2 V, CLPF = Open
CLPF = 1000 pF, f
SPOT
≤ 100 kHz
Pin VSET
To ±1 dB error
f = 900 MHz
f = 900 MHz, into 1:4 balun
Pin VREF
25°C
−40°C ≤ T
A
≤ +85°C
100
4.9
50
±0.5
100
200
0.1
0.32
3.44
48
60
5
45
0.4
70
0.5
46
−64
−77
1.225
68
50
−60
−73
1.25
0.08
8
3.75
54
−56
−69
1.275
4.9
0.48
3.52
V
V
V
mA
V/μs
V/μs
ns
μs
nV/√Hz
V
kΩ
mV/dB
dBm
dBV
V
mV/°C
Ω
Rev. D | Page 3 of 32
AD [ ANALOG DEVICES ]
