AD828
LOW DISTORTION LINE DRIVER
1.1kꢃ
The AD828 can quickly be turned into a powerful, low distor-
tion line driver (see Figure 10). In this arrangement, the AD828
can comfortably drive a 75 Ω back-terminated cable with a
5 MHz, 2 V p-p input, while achieving the harmonic distortion
performance outlined in the following table.
+V
S
1kꢃ
1ꢁF
0.1ꢁF
2
3
8
1/2
AD828
1
Configuration
2nd Harmonic
R
7.5ꢃ
C
1. No Load
2. 150 Ω RL Only
3. 150 Ω RL 7.5 Ω RC
–78.5 dBm
–63.8 dBm
–70.4 dBm
1kꢃ
1kꢃ
R
6
5
L
75ꢃ
1/2
V
In this application, one half of the AD828 operates at a gain of +2.1
and supplies the current to the load, while the other provides the
overall system gain of +2. This is important for two reasons: the
first is to keep the bandwidth of both amplifiers the same, and
the second is to preserve the AD828’s ability to operate from low
supply voltage. RC varies with the load and must be chosen to
satisfy the following equation:
IN
7
AD828
4
75ꢃ
1ꢁF
75ꢃ
0.1ꢁF
–V
S
Figure 10. Low Distortion Amplifier
RC = MRL
where M is defined by [(M + 1) GS = GD] and GD = Driver’s
Gain, GS = System Gain.
OUTLINE DIMENSIONS
8-Lead Plastic Dual-in-Line Package [PDIP]
(N-8)
8-Lead Standard Small Outline Package [SOIC]
(R-8)
Dimensions shown in inches and (millimeters)
Dimensions shown in millimeters and (inches)
0.4299 (10.92)
0.3480 (8.84)
5.00 (0.1968)
4.80 (0.1890)
8
5
4
8
1
5
4
0.2799 (7.11)
0.2402 (6.10)
6.20 (0.2440)
5.80 (0.2284)
0.1574 (4.00)
0.1497 (3.80)
1
PIN 1
PIN 1
0.3248 (8.25)
0.3000 (7.62)
0.1000 (2.54)
BSC
0.50 (0.0196)
0.25 (0.0099)
1.27 (0.0500)
BSC
ꢆ 45ꢀ
0.0598 (1.52)
0.0150 (0.38)
0.2098
(5.33)
MAX
1.75 (0.0688)
1.35 (0.0532)
COPLANARITY
0.25 (0.0098)
0.10 (0.0040)
0.1949 (4.95)
0.1154 (2.93)
8ꢀ
0.1299
(3.30)
MIN
0.1598 (4.06)
0.1154 (2.93)
0ꢀ 1.27 (0.0500)
0.51 (0.0201)
0.33 (0.0130)
0.0150 (0.38)
0.0079 (0.20)
0.25 (0.0098)
0.19 (0.0075)
SEATING
PLANE
0.41 (0.0160)
0.0220 (0.56)
0.0142 (0.36)
SEATING
PLANE
0.0697 (1.77)
0.0453 (1.15)
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COMPLIANT TO JEDEC STANDARDS MS-012 AA
Revision History
Location
Page
6/02–Data Sheet changed from REV. B to REV. C.
Renumbered Figures and TPCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Global
Changes to Figure 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
–12–
REV. C
ADI [ ADI ]
