AD827
Model
OUTPUT RESISTANCE
POWER SUPPLY
Operating Range
Quiescent Current
T
MIN
to T
MAX
T
MIN
to T
MAX
TRANSISTOR COUNT
92
Conditions
Open Loop
±
4.5
10
10.5
V
S
Min
AD827J
Typ Max
15
±
18
13
16
13.5
16.5
±
4.5
10
10.5
92
Min
AD827A/S
Typ Max
15
±
18
13
16.5/17.5
13.5
17/18
Unit
Ω
V
mA
mA
mA
mA
±
5 V
±
15 V
NOTES
1
Offset voltage for the AD827 is guaranteed after power is applied and the device is fully warmed up. All other specifications are measured using high speed test equipment,
approximately 1 second after power is applied.
2
Full Power Bandwidth = Slew Rate/2
π
V
PEAK
.
3
Gain = +1, rising edge.
All min and max specifications are guaranteed.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
1
ORDERING GUIDE
Model
AD827JN
AD827JR
AD827AQ
AD827SQ
AD827SQ/883B
5962-9211701MPA
AD827SE/883B
5962-9211701M2A
AD827JR-REEL
AD827JChips
AD827SChips
Temperature
Range
0°C to +70°C
0°C to +70°C
–40°C to +85°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
0°C to +70°C
0°C to +70°C
–55°C to +125°C
Package
Description
8-Lead Plastic DIP
16-Lead Plastic SO
8-Lead Cerdip
8-Lead Cerdip
8-Lead Cerdip
8-Lead Cerdip
20-Lead LCC
20-Lead LCC
Tape & Reel
Die
Die
Package
Option
N-8
R-16
Q-8
Q-8
Q-8
Q-8
E-20A
E-20A
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
±
18 V
Internal Power Dissipation
2
Plastic (N) Package (Derate at 10 mW/°C) . . . . . . . . 1.5 W
Cerdip (Q) Package (Derate at 8.7 mW/°C) . . . . . . . 1.3 W
Small Outline (R) Package (Derate at 10 mW/°C) . . . 1.5 W
LCC (E) Package (Derate at 6.7 mW/°C) . . . . . . . . . 1.0 W
Input Common-Mode Voltage . . . . . . . . . . . . . . . . . . . . .
±
V
S
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Output Short Circuit Duration
3
. . . . . . . . . . . . . . . . Indefinite
Storage Temperature Range (N, R) . . . . . . . –65°C to +125°C
Storage Temperature Range (Q) . . . . . . . . . –65°C to +150°C
Operating Temperature Range
AD827J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
AD827A . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
AD827S . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
Lead Temperature Range
(Soldering to 60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only, and functional operation of
the device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum ratings
for extended periods may affect device reliability.
2
Maximum internal power dissipation is specified so that T
J
does not exceed 175°C
at an ambient temperature of 25°C.
Thermal Characteristics:
MiniDIP:
θ
JA
= 100°C/W;
θ
JC
= 33°C/ W
Cerdip:
θ
JA
= 110°C/W;
θ
JC
= 30°C/W
16-Lead Small Outline Package:
θ
JA
= 100°C/W
20-Lead LCC:
θ
JA
= 150°C/W;
θ
JC
= 35°C/W
3
Indefinite short circuit duration is only permissible as long as the absolute
maximum power rating is not exceeded.
METALLIZATION PHOTOGRAPH
Contact factory for latest dimensions.
Dimensions shown in inches and (mm).
Substrate is connected to V+.
REV. C
–3–
AD [ ANALOG DEVICES ]
