欢迎访问ic37.com |
会员登录 免费注册
发布采购

AD7714ARS-5 参数 Datasheet PDF下载

AD7714ARS-5图片预览
型号: AD7714ARS-5
PDF下载: 下载PDF文件 查看货源
内容描述: 3 V / 5 V , CMOS , 500微安信号调理ADC [3 V/5 V, CMOS, 500 uA Signal Conditioning ADC]
分类和应用: 转换器光电二极管
文件页数/大小: 40 页 / 308 K
品牌: ADI [ ADI ]
 浏览型号AD7714ARS-5的Datasheet PDF文件第29页浏览型号AD7714ARS-5的Datasheet PDF文件第30页浏览型号AD7714ARS-5的Datasheet PDF文件第31页浏览型号AD7714ARS-5的Datasheet PDF文件第32页浏览型号AD7714ARS-5的Datasheet PDF文件第34页浏览型号AD7714ARS-5的Datasheet PDF文件第35页浏览型号AD7714ARS-5的Datasheet PDF文件第36页浏览型号AD7714ARS-5的Datasheet PDF文件第37页  
AD7714  
Table XV. C Code for Interfacing AD7714 to 68HC11  
/* This program has read and write routines for the 68HC11 to interface to the AD7714 and the sample  
program sets the various registers and then reads 1000 samples from the part. */  
#include <math.h>  
#include <io6811.h>  
#define NUM_SAMPLES 1000 /* change the number of data samples */  
#define MAX_REG_LENGTH 3 /* this says that the max length of a register is 3 bytes */  
Writetoreg (int);  
Read (int,char);  
char *datapointer = store;  
2
char store[NUM_SAMPLES*MAX_REG_LENGTH + 30];  
void main()  
{
/* the only pin that is programmed here from the 68HC11 is the /CS and this is why the PC2 bit  
of PORTC is made as an output */  
char a;  
DDRC = 0x04; /* PC2 is an output the rest of the port bits are inputs */  
PORTC | = 0x04; /* make the /CS line high */  
Writetoreg(0x27); /* set the channel AIN6/AIN6 and set the next operation as write to the filter high  
register */  
Writetoreg(0x4f); /* set Bipolar mode, 24 bits, boost off, all 4 MSBs of filterword to 1 */  
Writetoreg(0x37); /* set the next operation as a write to the filter low register */  
Writetoreg(0xA0); /* max filter word allowed for low part of the filterword */  
Writetoreg(0x17); /* set the operation as a write to the mode register */  
Writetoreg(0x20); /* set gain to 1, burnout current off, no filter sync, and do a self calibration */  
while(PORTC & 0x10); /* wait for /DRDY to go low */  
for(a=0;a<NUM_SAMPLES;a++);  
{
Writetoreg(0x5f); /*set the next operation for 24 bit read from the data register */  
Read(NUM_SAMPES,3);  
}
}
Writetoreg(int byteword);  
{
int q;  
SPCR = 0x3f;  
SPCR = 0X7f; /* this sets the WiredOR mode(DWOM=1), Master mode(MSTR=1), SCK idles high(CPOL=1), /SS  
can be low always (CPHA=1), lowest clock speed(slowest speed which is master clock /32 */  
DDRD = 0x18; /* SCK, MOSI outputs */  
q = SPSR;  
q = SPDR; /* the read of the staus register and of the data register is needed to clear the interrupt  
which tells the user that the data transfer is complete */  
PORTC &= 0xfb; /* /CS is low */  
SPDR = byteword; /* put the byte into data register */  
while(!(SPSR & 0x80)); /* wait for /DRDY to go low */  
PORTC |= 0x4; /* /CS high */  
}
Read(int amount, int reglength)  
{
int q;  
SPCR = 0x3f;  
SPCR = 0x7f; /* clear the interupt */  
DDRD = 0x10; /* MOSI output, MISO input, SCK output */  
while(PORTC & 0x10); /* wait for /DRDY to go low */  
PORTC & 0xfb ; /* /CS is low */  
for(b=0;b<reglength;b++)  
{
SPDR = 0;  
while(!(SPSR & 0x80)); /* wait until port ready before reading */  
*datapointer++=SPDR; /* read SPDR into store array via datapointer */  
}
PORTC|=4; /* /CS is high */  
}
REV. C  
–33–  
 复制成功!