欢迎访问ic37.com |
会员登录 免费注册
发布采购

AD623ARZ-R7 参数 Datasheet PDF下载

AD623ARZ-R7图片预览
型号: AD623ARZ-R7
PDF下载: 下载PDF文件 查看货源
内容描述: 单电源,轨到轨,低成本仪表放大器 [Single-Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier]
分类和应用: 仪表放大器放大器电路光电二极管
文件页数/大小: 24 页 / 1431 K
品牌: AD [ ANALOG DEVICES ]
 浏览型号AD623ARZ-R7的Datasheet PDF文件第13页浏览型号AD623ARZ-R7的Datasheet PDF文件第14页浏览型号AD623ARZ-R7的Datasheet PDF文件第15页浏览型号AD623ARZ-R7的Datasheet PDF文件第16页浏览型号AD623ARZ-R7的Datasheet PDF文件第18页浏览型号AD623ARZ-R7的Datasheet PDF文件第19页浏览型号AD623ARZ-R7的Datasheet PDF文件第20页浏览型号AD623ARZ-R7的Datasheet PDF文件第21页  
AD623
INPUT AND OUTPUT OFFSET VOLTAGE
The low errors of the AD623 are attributed to two sources,
input and output errors. The output error is divided by the
programmed gain when referred to the input. In practice,
the input errors dominate at high gains and the output errors
dominate at low gains. The total V
OS
for a given gain is calculated
as the following:
Total Error RTI
=
Input Error
+ (
Output Error
/
G
)
Total Error RTO
= (
Input Error
×
G
) +
Output Error
the in-amp. Resistor R1 and Capacitor C1 (and likewise, R2 and
C2) form a low-pass RC filter that has a −3 dB bandwidth equal
to
F
= 1/(2 π
R1C1
). Using the component values shown, this
filter has a −3 dB bandwidth of approximately 40 kHz. Resistors
R1 and R2 were selected to be large enough to isolate the input of
the circuit from the capacitors, but not large enough to significantly
increase the noise of the circuit. To preserve common-mode rejection
in the amplifier’s pass band, Capacitors C1 and C2 need to be 5%
or better units, or low cost 20% units can be tested and binned
to provide closely matched devices.
+V
S
0.33µF
R1
4.02kΩ
1%
C1
1000pF
5%
R
G
0.01µF
RTI offset errors and noise voltages for different gains are
shown in Table 6.
INPUT PROTECTION
Internal supply referenced clamping diodes allow the input,
reference, output, and gain terminals of the AD623 to safely
withstand overvoltages of 0.3 V above or below the supplies.
This is true for all gains and for power on and power off. This
last case is particularly important because the signal source
and amplifier may be powered separately.
If the overvoltage is expected to exceed this value, the current
through these diodes should be limited to about 10 mA using
external current limiting resistors (see Figure 44). The size of
this resistor is defined by the supply voltage and the required
overvoltage protection.
+V
S
I = 10mA MAX
V
OVER
R
LIM
R
LIM
–V
S
R
G
R
LIM
=
–IN
+IN
R2
C3
4.02kΩ 0.047µF
1%
C2
1000pF
5%
AD623
V
OUT
REFERENCE
0.33µF
0.01µF
Figure 45. Circuit to Attenuate RF Interference
AD623
OUTPUT
V
OVER
–V
S
+ 0.7V
00778-043
V
OVER
10mA
Figure 44. Input Protection
RF INTERFERENCE
All instrumentation amplifiers can rectify high frequency out-
of-band signals. Once rectified, these signals appear as dc offset
errors at the output. The circuit in Figure 45 provides good RFI
suppression without reducing performance within the pass band of
Table 6. RTI Error Sources
Gain
1
2
5
10
20
50
100
1000
Maximum Total Input Offset Error (μV)
AD623A
AD623B
1200
600
700
350
400
200
300
150
250
125
220
110
210
105
200
100
Capacitor C3 is needed to maintain common-mode rejection at
the low frequencies. R1/R2 and C1/C2 form a bridge circuit whose
output appears across the input pins of the in-amp. Any mismatch
between C1 and C2 unbalances the bridge and reduces the
common-mode rejection. C3 ensures that any RF signals are
common mode (the same on both in-amp inputs) and are not
applied differentially. This second low-pass network, R1 + R2 and
C3, has a −3 dB frequency equal to 1/(2 π (R1 + R2) (C3)). Using a
C3 value of 0.047 μF, the −3 dB signal bandwidth of this circuit is
approximately 400 Hz. The typical dc offset shift over frequency is
less than 1.5 μV and the circuit’s RF signal rejection is better than
71 dB. The 3 dB signal bandwidth of this circuit may be increased
to 900 Hz by reducing Resistors R1 and R2 to 2.2 kΩ. The
performance is similar to using 4 kΩ resistors, except that the
circuitry preceding the in-amp must drive a lower impedance load.
Maximum Total Input Offset Drift (μV/°C)
AD623A
AD623B
12
11
7
6
4
3
3
2
2.5
1.5
2.2
1.2
2.1
1.1
2
1
Total Input Referred Noise (nV/√Hz)
AD623A and AD623B
62
45
38
35
35
35
35
35
Rev. D | Page 17 of 24
00778-044
+V
S
NOTES:
1. LOCATE C1 TO C3 AS CLOSE TO THE INPUT PINS AS POSSIBLE.