AD8036/AD8037–SPECIFICATIONS
(±VS = ±5 V; RLOAD = 100 Ω; AV = +1 (AD8036); AV = +2 (AD8037), VH, VL open, unless
otherwise noted)
ELECTRICAL CHARACTERISTICS
AD8036A
AD8037A
Min Typ Max Units
Parameter
Conditions
Min
Typ
Max
DYNAMIC PERFORMANCE
Bandwidth (–3 dB)
Small Signal
VOUT ≤ 0.4 V p-p
8036, VOUT = 2.5 V p-p; 8037, VOUT = 3.5 V p-p 160
OUT ≤ 0.4 V p-p
8036, RF = 140 Ω; 8037, RF = 274 Ω
OUT = 4 V Step, 10–90%
VOUT = 0.5 V Step, 10–90%
OUT = 4 V Step, 10–90%
150
240
195
200 270
160 190
MHz
MHz
Large Signal1
Bandwidth for 0.1 dB Flatness
V
130
1200
1.4
130
1100 1500
1.2
MHz
V/µs
ns
Slew Rate, Average +/–
Rise/Fall Time
V
900
V
2.6
2.2
ns
Settling Time
To 0.1%
To 0.01%
VOUT = 2 V Step
VOUT = 2 V Step
10
16
10
16
ns
ns
HARMONIC/NOISE PERFORMANCE
2nd Harmonic Distortion
2 V p-p; 20 MHz, RL = 100 Ω
RL = 500 Ω
–59
–66
–68
–72
+46
18
–52
–59
–61
–65
–52 –45
dBc
dBc
dBc
dBc
dBm
dB
–72 –65
–70 –63
–80 –73
+41
3rd Harmonic Distortion
2 V p-p; 20 MHz, RL = 100 Ω
RL = 500 Ω
3rd Order Intercept
Noise Figure
25 MHz
RS = 50 Ω
14
Input Voltage Noise
Input Current Noise
1 MHz to 200 MHz
1 MHz to 200 MHz
6.7
2.2
4.5
2.1
nV√Hz
pA√Hz
Average Equivalent Integrated
Input Noise Voltage
Differential Gain Error (3.58 MHz)
Differential Phase Error (3.58 MHz)
Phase Nonlinearity
0.1 MHz to 200 MHz
95
60
µV rms
%
Degree
Degree
R
L = 150 Ω
0.05
0.02
1.1
0.09
0.04
0.02 0.04
0.02 0.04
1.1
RL = 150 Ω
DC to 100 MHz
CLAMP PERFORMANCE
Clamp Voltage Range2
Clamp Accuracy
VCH or VCL
2× Overdrive, VCH = +2 V, VCL = –2 V
TMIN–TMAX
± 3.3 ± 3.9
± 3
± 3.3 ± 3.9
± 3
V
± 10
± 20
± 10
± 20
mV
mV
mV
µA
µA
MHz
%
Clamp Nonlinearity Range3
Clamp Input Bias Current (VH or VL)
100
± 40
100
± 50 ± 70
± 90
8036, VH, L = ±1 V; 8037, VH, L = ± 0.5 V
TMIN–TMAX
VCH or VCL = 2 V p-p
2× Overdrive, VCH or VCL = 2 V p-p
2× Overdrive
± 60
± 80
Clamp Input Bandwidth (–3 dB)
Clamp Overshoot
Overdrive Recovery
150
240
1
180 270
5
1
1.3
5
1.5
ns
DC PERFORMANCE4, RL = 150 Ω
Input Offset Voltage5
2
7
11
2
7
10
mV
mV
µV/°C
µA
TMIN–TMAX
Offset Voltage Drift
Input Bias Current
± 10
4
± 10
3
10
15
3
9
15
3
T
MIN–TMAX
µA
Input Offset Current
0.3
0.1
µA
TMIN–TMAX
CM = ± 2 V
VOUT = ±2.5 V
TMIN–TMAX
5
5
µA
Common-Mode Rejection Ratio
Open-Loop Gain
V
66
48
40
90
55
70
54
46
90
60
dB
dB
dB
INPUT CHARACTERISTICS
Input Resistance
500
1.2
± 2.5
500
1.2
± 2.5
kΩ
pF
V
Input Capacitance
Input Common-Mode Voltage Range
OUTPUT CHARACTERISTICS
Output Voltage Range, RL = 150 Ω
Output Current
Output Resistance
Short Circuit Current
± 3.2 ± 3.9
± 3.2 ± 3.9
V
mA
Ω
70
0.3
240
70
0.3
240
mA
POWER SUPPLY
Operating Range
Quiescent Current
± 3.0 ± 5.0 ± 6.0
± 3.0 ± 5.0 ± 6.0
18.5 19.5
24
V
mA
mA
20.5
21.5
25
T
MIN–TMAX
Power Supply Rejection Ratio
TMIN–TMAX
50
60
56
66
dB
NOTES
1See Max Ratings and Theory of Operation sections of data sheet.
2See Max Ratings.
3Nonlinearity is defined as the voltage delta between the set input clamp voltage (VH or VL) and the voltage at which VOUT starts deviating from VIN (see Figure 73).
4Measured at AV = 50.
5Measured with respect to the inverting input.
Specifications subject to change without notice.
–2–
REV. A
ADI [ ADI ]
