ADG528A/ADG529A
TERMINOLOGY
RON
Ohmic resistance between terminals D and S
tOFF (EN)
Delay time between the 50% and 10% points of
the digital input and switch “OFF” condition
RON Match Difference between the RON of any two channels
RON Drift
IS (OFF)
Change in RON versus temperature
Source terminal leakage current when the switch
is off.
tTRANSITION Delay time between the 50% and 90% points of
the digital inputs and switch “ON” condition
when switching from one address state to another.
ID (OFF)
ID (ON)
Drain terminal leakage current when the switch is
off.
Leakage current that flows from the closed switch
into the body.
Analog voltage on terminal S or D
Channel input capacitance for “OFF” condition
Channel output capacitance for “OFF” condition
Digital input capacitance
tOPEN
“OFF” time measured between 50% points of
both switches when switching from one address
state to another
Maximum input voltage for Logic “0”
Minimum input voltage for Logic “1”
Input current of the digital input
Most positive voltage supply
VINL
VINH
IINL (IINH
VDD
VS (VD)
CS (OFF)
CD (OFF)
CIN
)
VSS
Most negative voltage supply
tON (EN)
Delay time between the 50% and 90% points of
the digital input and switch “ON” condition.
IDD
ISS
Positive supply current
Negative supply current
OUTLINE DIMENSIONS
18-Lead Plastic Dual In-Line Package [PDIP]
(N-18)
Dimensions shown in inches and (millimeters)
0.885 (22.48)
0.845 (21.46)
0.295 (7.49)
0.275 (6.99)
18
1
10
9
0.325 (8.26)
0.300 (7.62)
0.180 (4.57)
MAX
0.180 (4.57)
MAX
0.015 (0.38) MIN
0.150 (3.81)
0.110 (2.79)
0.015 (0.381)
0.008 (0.203)
SEATING
PLANE
0.100
(2.54)
BSC
0.060 (1.52)
0.045 (1.14)
0.022 (0.558)
0.014 (0.356)
COMPLIANT TO JEDEC STANDARDS MO-095AD
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
20-Lead Plastic Leaded Chip Carrier [PLCC]
(P-20A)
Dimensions shown in inches and (millimeters)
0.180 (4.57)
0.048 (1.21)
0.165 (4.19)
0.042 (1.07)
0.056 (1.42)
0.042 (1.07)
0.020 (0.50)
R
0.20 (0.51)
MIN
3
4
19
0.021 (0.53)
0.013 (0.33)
0.048 (1.21)
0.042 (1.07)
18
14
0.050
(1.27)
BSC
0.330 (8.38)
0.290 (7.37)
BOTTOM
VIEW
TOP VIEW
(PINS DOWN)
0.032 (0.81)
0.026 (0.66)
(PINS UP)
8
9
13
0.020
(0.50)
R
0.040 (1.01)
0.025 (0.64)
R
0.356 (9.04)
0.350 (8.89)
SQ
0.120 (3.04)
0.090 (2.29)
0.395 (10.02)
0.385 (9.78)
SQ
COMPLIANT TO JEDEC STANDARDS MO-047AA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
–10–
REV. B
ADI [ ADI ]
