Evaluation Board User Guide
UG-317
EVALUATION BOARD HARDWARE CONFIGURATION
TEST SETUP
JUMPER SETTINGS
The ADM2682E/ADM2687E evaluation board is shown
in Figure 2 with the default jumper settings on LK1 through
LK4 (driver and receiver enabled), power connection on J1,
input signal connection on J2, and probes attached to RXD,
TXD, Y, and Z for a loopback test (LK5 and LK6 are closed
to connect A to Y and B to Z).
The inputs to the ADM2682E/ADM2687E can be configured
using the jumpers on the evaluation board (see Table 1). Note
that multiple jumper blocks should not be placed on LK1 to
LK4 because the input sources may be shorted together. For
each link, a single jumper block can be moved from one posi-
tion to another, as specified in Table 1.
3.3V OR 5V
POWER
SUPPLY
SIGNAL
GENERATOR
OSCILLOSCOPE
J1
EVAL-ADM2682E_87EEBZ
LK1
GND1
J3
A
B
RXD
GND2
LK2
VCC
A
B
C
D
A
B
Z
LK6
LK5
RXD
RE
A
RXD
RE
B
Z
Y
DE
TXD
LK3
LK4
DE
A
B
C
Y
VISO
TXD
SHIELD
TXD
A
B
J4
J2
Figure 2. Basic Operation of the Evaluation Board for the ADM2682E/ADM2687E Isolated RS-485 Transceivers
Table 1. Jumper Configuration
Link
Connection Description
LK1
A
B
A
B
C
D
Connects the receiver output (RxD) of the ADM2682E/ADM2687E to the J3 connector.
Connects the receiver output (RxD) of the ADM2682E/ADM2687E to the J8-1 terminal block connector.
Connects the receiver enable input (RE) of the ADM2682E/ADM2687E to VCC. This setting disables the receiver.
Connects the receiver enable input (RE) of the ADM2682E/ADM2687E to GND1. This setting enables the receiver.
Connects the receiver enable input (RE) of the ADM2682E/ADM2687E to the J8-2 terminal block connector.
LK2
Connects the receiver enable input (RE) of the ADM2682E/ADM2687E to the driver enable input (DE); that is, the
input for both RE and DE is set by LK3. This setting ensures that when the driver is enabled, the receiver is
disabled, or when the driver is disabled, the receiver is enabled.
LK3
A
B
C
Connects the driver enable input (DE) of the ADM2682E/ADM2687E to VCC. This setting enables the driver.
Connects the driver enable input (DE) of the ADM2682E/ADM2687E to GND1. This setting disables the driver.
Connects the driver enable input (DE) of the ADM2682E/ADM2687E to the J8-3 terminal block connector.
Connects the driver input (TxD) of the ADM2682E/ADM2687E to the J8-4 terminal block connector.
Connects the driver input (TxD) of the ADM2682E/ADM2687E to the J2 connector.
LK4
LK5
A
B
Closed
Connects the ADM2682E/ADM2687E Receiver Input A to Driver Output Y. When LK5 and LK6 are both connected,
the evaluation board is configured for half-duplex operation.
Open
When LK5 and LK6 are both open, the evaluation board is configured for full-duplex operation.
LK6
Closed
Connects the ADM2682E/ADM2687E Receiver Input B to Driver Output Z. When LK5 and LK6 are both connected,
the evaluation board is configured for half-duplex operation.
Open
When LK5 and LK6 are both open, the evaluation board is configured for full-duplex operation.
Rev. 0 | Page 3 of 12
ADI [ ADI ]
