欢迎访问ic37.com |
会员登录 免费注册
发布采购

ACT2813 参数 Datasheet PDF下载

ACT2813图片预览
型号: ACT2813
PDF下载: 下载PDF文件 查看货源
内容描述: [5V/2.4A Power Bank Solution]
分类和应用:
文件页数/大小: 23 页 / 646 K
品牌: ACTIVE-SEMI [ ACTIVE-SEMI, INC ]
 浏览型号ACT2813的Datasheet PDF文件第1页浏览型号ACT2813的Datasheet PDF文件第2页浏览型号ACT2813的Datasheet PDF文件第4页浏览型号ACT2813的Datasheet PDF文件第5页浏览型号ACT2813的Datasheet PDF文件第6页浏览型号ACT2813的Datasheet PDF文件第7页浏览型号ACT2813的Datasheet PDF文件第8页浏览型号ACT2813的Datasheet PDF文件第9页  
ACT2813/ACT2813C  
Rev 2, 19-May-15  
PIN DESCRIPTIONS  
PIN  
NAME  
DESCRIPTION  
1
LED1  
Battery level indicator. An internal 3.5mA sink current limit is built in.  
Fast charge current setting pin. Connect a resistor from this pin to AGND to set the  
charge current. The current setting ranges from 1.0A-3.0A.  
2
3
4
ICST  
IOST  
CSP  
Output current setting. Connect a resistor from this pin to AGND to set output constant  
current. The current setting ranges from 1.0A-3.0A.  
Positive terminal of charge current sense input. Kevin sense is required with 10nF  
ceramic capacitor right across CSP and CSN pins.  
Battery input and negative terminal of charge current sense input. Connected to the  
battery pack positive terminal to provide power in High-Z mode. Bypass to PGND with  
a high quality ceramic capacitor placed as close to the IC as possible.  
5
6
VBAT/CSN  
PGND  
Power ground. PGND is connected to the source of low-side N-channel MOSFET and  
the MOSFET’s gate driver. PGND must be connected to AGND externally through  
ground plane.  
7, 8  
9
SW  
VOUT  
VIN  
Internal switch to output inductor terminal.  
Output pin. Bypass to PGND with a high quality low ESR and ESL ceramic capacitor  
placed as close to the IC as possible.  
10  
11  
USB or AC adaptor input. When VIN is valid, charge and power path is enabled.  
Analog ground. AGND must be connected to PGND externally through ground plane.  
AGND  
Drive external P-FET to protect output short circuit and leakage during shutdown. nPG  
pin is pulled up to VOUT internally. nPG pin is pulled low if VOUT is in the range.  
12  
13  
nPG  
PB  
Push button input, connect a push button from this pin to AGND, internally pulled up  
by a 3Mresistor to battery. PB starts up boost converter if HZ pin is grounded and  
VIN is not present. When this pin is pushed for 30ms, LED1-4 indicators are enable for  
5 seconds.  
Boost/high-Z mode enable pin, internally pulled up by a 3Mresistor to battery. When  
HZ pin is pulled ground, boost is enabled if VIN is not present.  
14  
15  
HZ  
TH: ACT2813  
Temperature sensing input. Connect to battery thermistor terminal. If no use, put 10K  
pulled down resistor.  
TH/FLD  
FLD: ACT2813C  
Open-drain flashlight driver. A internal switch can handle up to 50mA.  
Battery level voltage shift. Connect a resistor from this pin to AGND to shift the battery  
LED indication thresholds.  
16  
17  
BLVS  
RIMC  
Battery impendence compensation input. Connect to a resistor from this pin to APNG  
to program the battery impedance.  
18  
19  
20  
21  
LED4  
LED3  
LED2  
EP  
Battery level indicator. An internal 3.5mA sink current limit is built in.  
Battery level indicator. An internal 3.5mA sink current limit is built in.  
Battery level indicator. An internal 3.5mA sink current limit is built in.  
Exposed pad. Must be soldered to ground on the PCB.  
Innovative PowerTM  
- 3 -  
www.active-semi.com  
Copyright © 2015 Active-Semi, Inc.