OUTPUT VOLTAGE & CURRENT RATINGS
CPB
Output
Current
Regulation
Ripple
Efficiency(3)
Model
Voltage
Max
120 A
120 A
80 A
53 A
43 A
27 A
18 A
13 A
Peak
Line
Load
40 mV
40 mV
Noise(2)
120 mV
120 mV
150 mV
150 mV
150 mV
150 mV
200 mV
200 mV
3.3 V (2.64-3.96)
5.0 V (3.96-6.00)
7.5 V (5.25-8.25)
12.0 V (8.25-13.2)
15.0 V (10.50-16.5)
24.0 V (16.5-26.4)
36.0 V (25.2-39.6)
48.0 V (38.4-56.0)
-
-
-
-
-
20 mV
20 mV
36 mV
48 mV
60 mV
96 mV
144 mV
192 mV
72%
77%
79%
82%
82%
84%
84%
83%
CPB600PS3V3
CPB600PS05
CPB600PS7V5
CPB600PS12
CPB600PS15
CPB600PS24
CPB600PS36
CPB600PS48
60 mV
100 mV
120 mV
150 mV
150 mV
300 mV
(1)
31 A
-
Notes
1. Peak current duration 100 ms max with a duty cycle ≤35% 170-264 VAC only.
2. Measured over a 20 MHz bandwidth and from 0 °C to +50 °C.
3. Measured at nominal 230 VAC input and 100% load.
•
Mechanical Details
Weight 3.4kg
Output Voltage Adjustment
CN1/CN2 PIN CONNECTIONS
CN3 PIN CONNECTIONS
Function
Pin
1
Function
Pin
1
60-110% of the rated output voltage is achieved by:
+M
+S
-M
-S
+ Output Voltage Monitoring
-S
- Remote Sensing
1. Using on-board potentiometer.
2. Applying a voltage externally between TRM & -S
on CN1 or CN2.
3. Connecting a resistor externally between TRM & -S
on CN1 or CN2.
2
+ Remote Sensing
- Output Voltage Monitoring
- Remote Sensing
Voltage Balance
2
-S
- Remote Sensing
3
3
AUX
RC1
Auxiliary Output (12 V/0.1A)
Remote ON/OFF
4
4
5
VB
CB
5
AUXG AUX Ground
6
Current Balance
6
N.C.
PG
No Connection
The external voltage level is calculated below &
should not be less than -0.7 V or more than 3.0 V.
7
TRM Adjustment of Output Voltage
-S - Remote Sensing
7
Power Good Signal
Power Good Ground
8
8
PGG
9
RC2 Remote ON/OFF
Required Vout x 2.5
External Trim Voltage
=
10
RCG Remote ON/OFF Ground
Vnom
Mating Connector & Terminal for CN1, CN2 & CN3
Connector
Mating
Terminal
Mfr
Connector
Reel
SPHD-002T-P0.5
CN1
S10B-PHDSS PHDR-10VS
CN2
CN3 S8B-PHDSS
Loose
BPHD-001T-P0.5 J.S.T
BPHD-002T-P0.5
PHDR-8VS
www.xpplc.com
sales@xpplc.com
Rev 2.0
XPPOWER [ XP POWER LIMITED ]
