TS8G~32GCF600
600X CompactFlash Card
PC Card Memory Mode
PC Card I/O Mode
True IDE Mode4
Pin
Num
Pin
Type
In, Out
Type
Pin
Num
Pin
Signal Name
Type
In, Out
Type
Pin
Num
Pin
Type
In, Out
Type
Signal Name
Signal Name
-HIOE7
HSTROBE8
-HDMARDY9
-HIOE
-HIOE
34
HSTROBE10
HDMARDY11
I
I
I3U
34
HSTROBE10
-HDMARDY11
I
I
I3U
34
I
I
I3Z
-IOWR
STOP10,11
-WE
-IOWR
STOP10,11
-WE
-IOWR7
STOP8,9
-WE3
35
36
I3U
I3U
35
36
I3U
I3U
35
36
I3Z
I3U
I
I
I
37
38
39
40
41
READY
VCC
O
OT1
Power
I2Z
37
38
39
40
41
-IREQ
VCC
O
OT1
Power
I2Z
37
38
39
40
41
INTRQ
VCC
O
OZ1
Power
I2U
-CSEL5
I
O
I
-CSEL5
I
O
I
-CSEL
I
O
I
-VS2
OPEN
I2Z
-VS2
OPEN
I2Z
-VS2
OPEN
I2Z
RESET
RESET
-RESET
IORDY7
-DDMARDY8
DSTROBE9
-WAIT
-WAIT
ON1
-DDMARDY10
DSTROBE11
-INPACK
-DMARQ12
-REG
-DDMARDY10
DSTROBE11
-INPACK
-DMARQ12
-REG
42
O
OT1
42
O
OT1
42
O
OT113
43
44
O
I
OT1
I3U
43
44
O
I
OT1
I3U
43
44
DMARQ
O
I
OZ1
I3U
-DMACK 6
-DMACK 12
DMACK 12
45
46
BVD2
O
O
OT1
OT1
45
46
-SPKR
O
O
OT1
OT1
45
46
-DASP
I/O
I/O
I1U, ON1
I1U, ON1
BVD1
-STSCHG
-PDIAG
I1Z,
OZ3
I1Z,
OZ3
I1Z,
OZ3
I1Z,
OZ3
I1Z,
OZ3
I1Z,
OZ3
47
48
D081
D091
I/O
I/O
I/O
47
48
D081
D091
I/O
I/O
I/O
47
48
D081
D091
I/O
I/O
I/O
I1Z, OZ3
I1Z, OZ3
49
50
D101
GND
49
50
D101
GND
49
50
D101
GND
I1Z, OZ3
Ground
Ground
Ground
Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state
signals not to consume current.
2) The signal should be grounded by the host.
3) The signal should be tied to VCC by the host.
4) The mode is required for CompactFlash Storage Cards.
5) The -CSEL signal is ignored by the card in PC Card modes. However, because it is not pulled upon the card in these modes,
it should not be left floating by the host in PC Card modes. In these modes, the pin should be connected by the host to PC
Card A25 or grounded by the host.
6) If DMA operations are not used, the signal should be held high or tied to VCC by the host. For proper operation in older hosts: while DMA
operations are not active, the card shall ignore this signal,including a floating condition
7) Signal usage in True IDE Mode except when Ultra DMA mode protocol is active.
8) Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Write is active.
9) Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Read is active.
10) Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Write is active.
11) Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Read is active.
12) Signal usage in PC Card I/O and Memory Mode when Ultra DMA protocol is active.
Transcend Information Inc.
6
V1.0
TRANSCEND [ TRANSCEND INFORMATION. INC. ]
