欢迎访问ic37.com |
会员登录 免费注册
发布采购

TS256MCF100I 参数 Datasheet PDF下载

TS256MCF100I图片预览
型号: TS256MCF100I
PDF下载: 下载PDF文件 查看货源
内容描述: 工业用CF卡 [Industrial CF Card]
分类和应用:
文件页数/大小: 80 页 / 3420 K
品牌: TRANSCEND [ TRANSCEND INFORMATION. INC. ]
 浏览型号TS256MCF100I的Datasheet PDF文件第3页浏览型号TS256MCF100I的Datasheet PDF文件第4页浏览型号TS256MCF100I的Datasheet PDF文件第5页浏览型号TS256MCF100I的Datasheet PDF文件第6页浏览型号TS256MCF100I的Datasheet PDF文件第8页浏览型号TS256MCF100I的Datasheet PDF文件第9页浏览型号TS256MCF100I的Datasheet PDF文件第10页浏览型号TS256MCF100I的Datasheet PDF文件第11页  
Transcend Industrial CF Card  
(TS128M ~ 16GCF100I)  
Signal Description  
Signal Name  
A10 – A00  
Dir.  
I
Pin  
Description  
8,10,11,12, These address lines along with the -REG signal are used to select the following:  
14,15,16,17, The I/O port address registers within the CompactFlash Storage Card , the  
(PC Card Memory Mode)  
18,19,20  
memory mapped port address registers within the CompactFlash Storage Card,  
a byte in the card's information structure and its configuration control and status  
registers.  
A10 – A00  
This signal is the same as the PC Card Memory Mode signal.  
(PC Card I/O Mode)  
A02 - A00  
18,19,20  
In True IDE Mode, only A[02:00] are used to select the one of eight registers  
in the Task File, the remaining address lines should be grounded by the  
host.  
I
(True IDE Mode)  
BVD1  
I/O  
46  
This signal is asserted high, as BVD1 is not supported.  
(PC Card Memory Mode)  
-STSCHG  
This signal is asserted low to alert the host to changes in the READY and Write  
Protect states, while the I/O interface is configured. Its use is controlled by the  
Card Config and Status Register.  
(PC Card I/O Mode)  
Status Changed  
-PDIAG  
In the True IDE Mode, this input / output is the Pass Diagnostic signal in the  
Master / Slave handshake protocol.  
(True IDE Mode)  
BVD2  
I/O  
45  
This signal is asserted high, as BVD2 is not supported.  
(PC Card Memory Mode)  
-SPKR  
This line is the Binary Audio output from the card. If the Card does not support  
the Binary Audio function, this line should be held negated.  
(PC Card I/O Mode)  
-DASP  
In the True IDE Mode, this input/output is the Disk Active/Slave Present signal in  
the Master/Slave handshake protocol.  
(True IDE Mode)  
-CD1, -CD2  
O
26,25  
These Card Detect pins are connected to ground on the CompactFlash Storage  
Card. They are used by the host to determine that the CompactFlash Storage  
Card is fully inserted into its socket.  
(PC Card Memory Mode)  
-CD1, -CD2  
This signal is the same for all modes.  
This signal is the same for all modes.  
(PC Card I/O Mode)  
-CD1, -CD2  
(True IDE Mode)  
Transcend Information Inc.  
7
V1.2