欢迎访问ic37.com |
会员登录 免费注册
发布采购

78Q2133 参数 Datasheet PDF下载

78Q2133图片预览
型号: 78Q2133
PDF下载: 下载PDF文件 查看货源
内容描述: 10 / 100BASE -TX收发器 [10/100BASE-TX Transceiver]
分类和应用: 网络接口电信集成电路电信电路局域网(LAN)标准以太网:16GBASE-T
文件页数/大小: 42 页 / 730 K
品牌: TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
 浏览型号78Q2133的Datasheet PDF文件第4页浏览型号78Q2133的Datasheet PDF文件第5页浏览型号78Q2133的Datasheet PDF文件第6页浏览型号78Q2133的Datasheet PDF文件第7页浏览型号78Q2133的Datasheet PDF文件第9页浏览型号78Q2133的Datasheet PDF文件第10页浏览型号78Q2133的Datasheet PDF文件第11页浏览型号78Q2133的Datasheet PDF文件第12页  
78Q2123/78Q2133 MicroPHY™  
10/100BASE-TX Transceiver  
MII (MEDIA INDEPENDENT INTERFACE) (CONTINUED)  
SIGNAL  
PIN  
TYPE DESCRIPTION  
RX_DV  
11  
COZ RECEIVE DATA VALID: RX_DV is asserted high to indicate that valid data is  
present on the RXD[3:0] pins. In 100BASE-TX mode, it transitions high with the first  
nibble of the preamble and is pulled low when the last data nibble has been  
received. In 10BASE-T mode it transitions high when the start-of-frame delimiter  
(SFD) is detected. This pin is tri-stated in isolate mode.  
RXD[3:0]  
RX_ER  
[5:8]  
13  
COZ RECEIVE DATA: Received data is provided to the MAC via RXD[3:0]. These pins  
are tri-stated in isolate mode.  
COZ RECEIVE ERROR: RX_ER is asserted high when an error is detected during frame  
reception. In PCS bypass mode, this pin becomes the MSB of the receive 5-bit code  
group. This pin is tri-stated in isolate mode.  
MDC  
2
1
CIS  
MANAGEMENT DATA CLOCK: MDC is the clock used for transferring data via the  
MDIO pin.  
MDIO  
CIO  
MANAGEMENT DATA INPUT/OUTPUT: MDIO is a bi-directional port used to  
access management registers within the 78Q2123/78Q2133. This pin requires an  
external pull-up resistor as specified in IEEE-802.3.  
CONTROL AND STATUS  
SIGNAL  
PIN  
TYPE DESCRIPTION  
RST  
23  
CIS  
ACTIVE LOW RESET: When pulled low the pin resets the chip. The reset pulse  
must be long enough to guarantee stabilization of the supply voltage and startup of  
the oscillator. Refer to the Electrical Specifications for the reset pulse requirements.  
There are 2 other ways to reset the chip:  
i. Through the internal power-on-reset (activated when the chip is being powered  
up)  
ii. Through the MII register bit (MR 0.15)  
INTR  
32  
COZ INTERRUPT PIN: This pin is used to signal an interrupt to the media access  
controller. The pin is held in the high impedance state when an interrupt is not  
indicated. The pin will be forced high or low to signal an interrupt depending upon  
the value of the INPOL bit (MR16.14). The events which trigger an interrupt can be  
programmed via the Interrupt Control Register located at address MR17.  
Page: 8 of 42  
© 2009 Teridian Semiconductor Corporation  
Rev 1.5