78P2344JAT
4-port E3/DS3/STS-1 LIU
with Jitter Attenuator
FUNCTIONAL DESCRIPTION
The jitter tolerance of 78P2344JAT meets the
requirements of ITU-T G.823 for E3 rates; the
requirements of ITU-T G.824 and Telcordia GR-499
(Cat I and II) for DS3 rates; and the requirements of
Telcordia GR-253 for STS1 rates.
The 78P2344JAT contains all the necessary
transmit and receive circuitry for connection
between E3, DS3, or STS-1 line interfaces and
digital Framer/Mapper ICs.
OPERATING RATE
With the Jitter Attenuator disabled, the jitter transfer
function meets the requirements of GR-499 for
Category II DS3 interfaces.
The Master Control Register (MSCR) determines
which mode the device operates in according to the
table below. The MSL0 pin is also provided for
mode selection in applications without a serial
control interface. Upon power-up or reset, the state
of the MSL0 pin is sensed and mapped into the DS3
and E3 register bits representing the appropriate
mode of operation. After power-up/reset, the state of
the MSL0 pin is ignored.
When the Jitter Attenuator is enabled, the
78P2344JAT meets the requirements of GR-499
and GR-253 for all categories of DS3/STS1
equipment and the ETSI TBR-24 requirements for
E3 rates.
standards,
To check conformance with other
please refer to the JITTER
ATTENUATOR TRANSFER FUNCTION section for
more detailed info.
Standard
MSL0 pin
DS3 bit
E3 bit
RECEIVER MONITOR MODE
E3
DS3
STS-1
STS-1
L
H
Z
Z
0
1
0
1
1
0
0
1
When in monitor mode, 20dB of flat gain is applied
to the incoming signal before it is fed to the receive
equalizer. This mode is controlled by the MON bit in
the Mode Control Register.
RECEIVER OPERATION
SIGNAL DETECT
The receiver input is either transformer-coupled or
capacitor-coupled to the line signal. In applications
where the highest performance and isolation are
required, a 1:1 transformer is used in the receive
path. In applications where isolation is provided
elsewhere in the circuit, capacitor coupling can be
used. The receiver input should be line terminated
externally with a termination resistor.
When the received signal is below a minimum
threshold, the corresponding LOS signal (bit) is
asserted. A time delay is provided before this output
is active so that transient interruptions do not cause
false indications. The LOS signal can also be used
to trigger an interrupt on the INTRx pin when serial
interface control is not available. This is controlled
by setting the RXER bit in the Interrupt Control
Register (INTC).
The AMI signal first enters an AGC, which has a
selectable gain range setting. In normal operation,
the AGC can compensate for signals with up to 6dB
of flat loss. When Receiver Monitor Mode is
enabled, the AGC can compensate for a DSX3
monitor signal with 16 to 20 dB of flat loss. The
signal then enters a high performance adaptive
equalizer. The equalizer is designed to overcome
inter-symbol interference caused by long cable
lengths. Because the equalizer is adaptive, the
circuit will work with all square-shaped signals such
as DS3-high or 34.368 Mbit/s E3. The variable gain
differential amplifier automatically controls the gain
Note: In DS3 or STS-1 mode, when LBO is not
enabled, the transmitters have to be properly
terminated to ensure reliable LOS detection. If a
transmitter is not terminated, the resultant 2x signal
is large enough to couple to the neighboring
receivers through the ESD diodes, causing false
Signal Detect indication.
to maintain
a
constant voltage level output
regardless of the input voltage level.
Page 2 of 37
2005 Teridian Semiconductor Corporation
Rev 2.2
TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
