Series 732
DPDT Non-Latching
Commercial Electromechanical Relay
SERIES 732
GENERAL ELECTRICAL SPECIFICATIONS (@25°C)
Contact Arrangement
Rated Duty
2 Form C (DPDT)
Continuous
Contact Resistance
0.15 Ω max.; 0.25 Ω max. afterlife at A / 28 Vdc
Resistive:
Inductive:
Lamp:
1 A/ 28 Vdc
200 mA/ 28 Vdc (320mH)
100 mA / 28 Vdc (320mH)
10 to 50 μA @ 10 to 50 mV
Contact Load Rating (DC)
Low level:
Resistive: 250 mA / 115Vac, 60 and 400 Hz (Case not grounded)
100 mA / 115 Vac, 60 and 400 Hz (Case grounded)
Contact Load Rating (AC)
Contact Life Ratings
10,000,000 cycles (typical) at low level
1,000,000 cycles (typical) at 0.5 A / 28 Vdc resistive
100,000 cycles min. at all other loads specified above
Contact Overload Rating
Coil Operating Power
Contact Carry Rating
Operate Time
2 A / 28 Vdc Resistive (100 cycles min.)
200 mW typical at nominal rated voltage
Contact Factory
6.0 msec max. at nominal rated coil voltage
Release Time
732: 3.0 ms max.
0.4 pf typical
732D, 732TN: 7.5 ms max.
Intercontact Capacitance
Insulation Resistance
Dielectric Strength
1,000 MΩ min. between mutually isolated terminals
350 Vrms (60 Hz) @ atmospheric pressure
Negative Coil Transient (Vdc) 2.0 Vdc Max.
Diode P.I.V. (Vdc)
60 Vdc Min.
Base Voltage to Turn Off (Vdc)
0.3 min
6.0 min
60 min
732TN Transistor
Characteristics
Emitter-Base breakdown Voltage (BVEBO) (Vdc)
Collector-Base breakdown Voltage (BVCBO) (Vdc)
DETAILED ELECTRICAL SPECIFICATIONS (@25°C)
732-5
732D-5
732-6
732D-6
732-9
732D-9
732-12
732D-12
732-18
732D-18
732-26
732D-26
BASE PART NUMBERS (732, 732D, 732TN)
Nom.
732TN-5 732TN-6 732TN-9 732TN-12 732TN-18 732TN-26
5.0
7.5
6.0
10.0
200
4.5
9.0
15.0
400
6.8
12.0
20.0
850
9.0
18.0
30.0
1600
13.5
0.38
26.5
40.0
3300
18.0
0.24
Coil Voltage
Max.
Coil Resistance (Ohms ±20%)
100
3.5
1.5
Pick-up Voltage (Vdc, Max.) Pulse Operation
732TN Base Current to Turn On (mAdc, min.)
1.00
0.75
0.47
GENERAL NOTES
PERFORMANCE CURVES (Note 2)
1. Relay contacts will exhibit no chatter in
excess of 10 μsec or transfer in excess
of 1 μsec.
2. “Typical” characteristics are based on
available data and are best estimates.
No on-going verification tests are
performed.
3. Unless otherwise specified, parameters
are initial values.
4. Relays can be supplied with a spacer
pad. See appendix.
TYPICAL RF PERFORMANCE
TYPICAL DC CONTACT RATING (RESISTIVE)
0
.1
.2
.3
.4
300
250
200
10
20
30
40
50
60
70
1.92
1.22
1.07
1.02
1.01
1.00
1.00
150
100
50
0
0.1 0.2 0.3 0.4 0.5
0.6
0.7 0.8
0.9 1.0
.01
0.5
.1
.5
1.0
LOAD CURRENT (AMPS DC)
FREQUENCY (GHz)
FIGURE 2
FIGURE 1
732 Page 2
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2015 TELEDYNE RELAYS
732\122015\Q4
TELEDYNE [ TELEDYNE TECHNOLOGIES INCORPORATED ]
