SERIES 172
GENERAL ELECTRICAL SPECIFICATIONS (@25°C) (Notes 2 & 3)
Contact Arrangement
Rated Duty
2 Form C (DPDT)
Continuous
Contact Resistance
0.15 ohm max. before life; 0.3 ohm max. after life at 1A/28Vdc (measured 1/8" from header)
Resistive:
Inductive:
Lamp:
1 Amp/28Vdc
200 mA/28Vdc (320 mH)
100 mA/28Vdc
Contact Load Ratings (DC)
(See Fig. 1 for other DC
resistive voltage/current ratings)
Low Level:
10 to 50 µA/10 to 50mV
5,000,000 cycles (typical) at low level
Contact Life Ratings
500,000 cycles (typical) at 0.5A/28Vdc resistive
100,000 cycles min. at all other loads specified above
Contact Overload Rating
Contact Carry Rating
Operate Time
2A/28Vdc Resistive (100 cycles min.)
Contact factory
6.0 msec max. at nominal rated coil voltage
172: 3.0 msec max. 172D: 6.0 msec max.
0.4 pf typical
Release Time
Intercontact Capacitance
Insulation Resistance
Dielectric Strength
Negative Coil Transient 172
Diode P.I.V. 172D
1,000 megohms min. between mutually isolated terminals
Atmospheric pressure: 300 Vrms/60Hz
2.0 Vdc Max.
60 Vdc Min.
DETAILED ELECTRICAL SPECIFICATIONS (@25°C) (Note 3)
172-3
172D-3
172-5
172D-5
172-12
172D-12
172-26
172D-26
BASE PART
NUMBERS
Nom.
Max.
3.0
3.6
5.0
5.8
64
12.0
16.0
400
9.0
26.5
32.0
1600
18.0
440
Coil Voltage (Vdc)
Coil Resistance (Ohms ±20%)
39
Pick-up Voltage (Vdc, Max.) Pulse Operation
2.25
235
3.8
405
Coil Operating Power at Nominal Voltage (Milliwatts)
360
OUTLINE DIMENSIONS (Note 4)
SCHEMATIC DIAGRAM
CASE DETAIL
TERMINAL LOCATIONS
(Viewed from Terminals, Numbers for Reference Only)
.750 MIN.
.280 MAX
(19.05)
.031 REF
(.79)
.035 REF
(.89)
(7.11)
7
6
8
1
.335 SQ MAX.
(8.51)
2
172
.100 ±.010 TYP
(2.54 ±.25)
3
5
4
+.002
.017
(.43
DIA
–.001
.375
SQ MAX.
(8.51)
+.05
)
–.03
DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)
172D
SCHEMATIC IS VIEWED FROM TERMINALS
GENERAL NOTES
PERFORMANCE CURVES (Note 2)
1. Relay contacts will exhibit no chatter in
excess of 10 µsec or transfer in excess
of 1 µsec.
2. “Typical” characteristics are based on
available data and are best estimates.
No on-going verification tests are
performed.
3. Unless otherwise specified, parameters
are initial values.
4. Relays can be supplied with a spacer
pad. See appendix.
TYPICAL RF PERFORMANCE
TYPICAL DC CONTACT RATING (RESISTIVE)
0
.1
.2
.3
.4
300
250
200
10
20
30
40
50
60
70
1.92
1.22
1.07
1.02
1.01
1.00
1.00
150
100
50
0
0.1 0.2 0.3 0.4 0.5
0.6
0.7 0.8
0.9 1.0
.01
0.5
.1
.5
1.0
LOAD CURRENT (AMPS DC)
FREQUENCY (GHz)
FIGURE 2
FIGURE 1
172 Page 2
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
©2007 TELEDYNE RELAYS
172/0107/Q1