SMM605
Preliminary Information
ABSOLUTE MAXIMUM RATINGS
RECOMMENDED OPERATING CONDITIONS
Temperature Under Bias ...................... -55°C to 125°C
Temperature Range (Industrial)...........–40°C to +85°C
Storage Temperature............................ -65°C to 150°C
(Commercial)............–5°C to +70°C
VDD Supply Voltage..................................2.7V to 5.5V
12VIN Supply Voltage (1) ........................6.0V to 14.0V
VIN............................................................ GND to VDD
VOUT...................................................... GND to 15.0V
Package Thermal Resistance (θJA)
Terminal Voltage with Respect to GND:
VDD Supply Voltage ..........................-0.3V to 6.0V
12VIN Supply Voltage......................-0.3V to 15.0V
All Others ................................-0.3V to VDD + 0.7V
Output Short Circuit Current ............................... 100mA
48 Lead TQFP……………………………….…80oC/W
Lead Solder Temperature (10 secs)……………….300°C
Junction Temperature.......................…….....…...150°C
ESD Rating per JEDEC……………………..…..2000V
Moisture Classification Level 1 (MSL 1) per J-STD- 020
Latch-Up testing per JEDEC………..……....…±100mA
Note 1 – Range depends on internal regulator set to 3.6V or 5.5V,
see 12VIN specification below.
Note - The device is not guaranteed to function outside its operating
rating. Stresses listed under Absolute Maximum Ratings may cause
permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions
outside those listed in the operational sections of the specification is
not implied. Exposure to any absolute maximum rating for extended
periods may affect device performance and reliability. Devices are
ESD sensitive. Handling precautions are recommended.
DC OPERATING CHARACTERISTICS
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Supply Voltage
Notes
Min
Max
Unit
V
2.7
5.5
VDD
Internally regulated to 5.5V
Internally regulated to 3.6V
10
6
14
14
V
V
12VIN
Supply Voltage
All TRIM pins floating,
12VIN floating
All TRIM pins floating,
VDD floating
IDD
Power Supply Current from VDD
Power Supply Current from 12VIN
3
3
5
5
mA
mA
I12VIN
TRIM characteristics
TRIM Sourcing Maximum
1.5
1.5
mA
mA
V
TRIM output current through 100Ω to Current
ITRIM
1.0V
TRIM Sinking Maximum
Current
Depends on Trim range of
DC-DC Converter
VREF_CNTL/
4
VTRIM
Margin Control and ADOC Range
VDD
All other input and output characteristics
VDD = 2.7V
VDD = 5.0V
VDD = 2.7V
VDD = 5.0V
0.9xVDD
0.7xVDD
-0.1
VDD
VDD
0.1xVDD
0.3xVDD
V
V
V
V
Input High Voltage (FS,
VIH
PWR_ON/OFF, MR#, SDA, SCL)
Input Low Voltage (FS,
VIL
PWR_ON/OFF, MR#, SDA, SCL)
-0.1
Programmable Open Drain Outputs
VOL
ISINK = 1mA
0
0
0.4
1.0
V
(RST, HEALTHY, FAULT, PUPx)
Note – Total ISINK from all PUPx pins
should not exceed 3mA or ADOCACC
specification will be affected
IOL
Output Low Current
mA
Summit Microelectronics, Inc
2064 1.1 09/16/03
6