24PC Series (psi)
Unamplified, uncompensated pressure sensors
PRESSURE SENSOR CHARACTERISTICS
Vs = 10.0 ± 0.01 V, tamb = 25°C (unless otherwise noted)
Full-scale span2
Typ.
Listing
Order number
Operating pressure
Min.
Max.
46 mV
24PCEFAxx
24PCAFAxx
24PCBFAxx
24PCCFAxx
24PCDFAxx
24PCFFAxx
24PCGFAxx
24PC0035xxA
24PC0070xxA
24PC0350xxA
24PC1000xxA
24PC2000xxA
24PC7000xxA
24PC17K0xxA
0 - 0.5 psi (34.5 mbar)
0 - 1 psi (69 mbar)
24 mV
30 mV
85 mV
165 mV
240 mV
156 mV
145 mV
35 mV
45 mV
60 mV
0 - 5 psi (345 mbar)
0 - 15 psi (1034 mbar)
0 - 30 psi (2068 mbar)
0 - 100 psi (6.9 bar)
0 - 250 psi (17.2 bar)
115 mV
225 mV
330 mV
225 mV
212 mV
145 mV
285 mV
420 mV
294 mV
280 mV
COMMON PERFORMANCE CHARACTERISTICS
Vs = 10.0 ± 0.01 V, tamb = 25°C (unless otherwise noted)
Characteristics
Min.
Typ.
Max.
Unit
Zero pressure offset
Temperature effects (0 - 50°C)4
-30
+30
mV
Offset
Span
±2.0
-2000
+2200
±0.25
±0.15
±0.5
ppm/°C
% span
Temperature effects on bridge impedance4
Linearity (P2 > P1, BSL)3
Repeatability and hysteresis5
Long term stability7
±1.0
Input impedance
4.0
4.0
5.0
6.0
6.0
1.0
kΩ
Output impedance
Response time6
5.0
ms
Specification notes:
1. The maximum specified pressure which may be applied to the sensor without causing a permanent change in the output characteristics.
2. Span is the algebraic difference between the output voltage at full-scale pressure and the output at zero pressure. Span is
ratiometric to the supply voltage.
3. Linearity (BSL), the deviation of measured output at constant temperature (25°C) from "Best Straight Line" determined by three
points, offset pressure, full-scale pressure and half full-scale pressure.
Vfull scale - Voffset
(full scale pressure)
V
–
x (½ full scale pressure) + Voffset
: 2 (Vfull scale) x 100 %
[
{
}]
½ full scale
where: V = measured value for each device
4. Error band of the offset voltage, span or bridge impedance in the specified temperature range, relative to the 25°C reading.
5. Repeatability, the deviation in output readings for successive application of any given input pressure (all other conditions
remaining constant. Hysteresis, the error defined by the deviation in output signal obtained when a specific pressure point is
approached first with increasing pressure, then with decreasing pressure or vice versa (all other conditions remaining constant).
6. Response time for 0 to full-scale pressure step change, readings taken at 10 % and 90 % of full-scale pressure.
7. Long term stability of offset and span over a period over one year.
8. The sensors might be used on both ports, for media compatible with the components, specified under "Service" (page 1).
9. Other sealing materials are available on request. Minimum order quantities might be required.
10. Other pressure port styles, like barbed ones, luers, modular, M5, needle style or flow through connection, are
available on request. For these specials see the data sheet "24/26PC specials". Minimum order quantities might be required, call
Sensortechnics for assistance.
2/4
February 2005 / 603
www.sensortechnics.com
SENSORTECHNICS [ SENSORTECHNICS GMBH ]
