欢迎访问ic37.com |
会员登录 免费注册
发布采购

DOH16-12T-P 参数 Datasheet PDF下载

DOH16-12T-P图片预览
型号: DOH16-12T-P
PDF下载: 下载PDF文件 查看货源
内容描述: 非隔离式负载的DC / DC转换器点 [Non-isolated Point of load DC/DC converters]
分类和应用: 转换器
文件页数/大小: 3 页 / 219 K
品牌: RSG [ RSG ELECTRONIC COMPONENTS GMBH ]
 浏览型号DOH16-12T-P的Datasheet PDF文件第1页浏览型号DOH16-12T-P的Datasheet PDF文件第3页  
2 / 3  
Efficiency(%)  
ON/OFF  
Logic  
Output Current  
Model Name  
Package  
Input Voltage Output Voltage  
12Vin, 3.3Vdc@16A  
Min. Load  
Max. Load  
DOS16-12T  
DOS16-12T-P  
DOH16-12T  
DOH16-12T-P  
DOH16-12TA  
DOH16-12TA-P  
Negative  
Positive  
Negative  
Positive  
SMD  
Vo(set)3.63V  
Vin = 8.3-14Vdc  
0.75 ~ 5.0Vdc  
Vo(set)3.63V  
Vin = 8.3-13.2Vdc  
Vertical Mounting  
SIP  
0A  
16A  
92%  
Negative Horizontal Mounting  
SIP  
Positive  
Note  
1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC.  
MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment).  
2. External with C = 1μF ceramic//10μF tantalum capacitors.  
out  
3. External with C = 2×150μF polymer capacitors.  
out  
4. Output voltage programmable from 0.7525V to 5V by connecting a single resistor (shown as Rtrim in Table 1) between the TRIM and GND pins of the  
module.To calculate the value of the resistor Rtrim for a particular output voltage Vo, use the following equation:  
10500  
-1000  
]
Rtrim =  
[
Ω
Vo – 0.7525  
5. It’s necessary to equip the external input capacitors at the input of the module. The capacitors should connect as close as possible to the input  
terminals that ensuring module stability. The external C is 6×47μF ceramic capacitors at least.  
in  
6. Device code with suffix “-P” – Positive logic(On/Off is open collector/drain logic input; Signal referenced to GND )  
Device code with no suffix – Negative logic (On/Off pin is open collector/drain logic input with external pull –up resistor; signal referenced to GND)  
7. Case 1 :On/Off input is set to logic low (module on) and then input power is applied (delay from instant at which Vin=Vin(min) until Vo=10% of Vo(set))  
8. Case 2 :Input power is applied for at least one second and then the On/Off input is set to logic low (delay form instant at which Von/off=0.3V until  
Vo=10% of Vo(set))  
CAUTION: This power module is not internally fused. An input line fuse must always be used.  
DOS16-12T, Vo=3.3V, Derating Curve  
18  
16  
14  
12  
10  
8
6
4
2
0
20  
30  
40  
50  
60  
70  
80  
90  
Fig. 1  
AMBIENT TEMPERATURE,TA(  
)
Table 1  
Rtrim (KΩ)  
Vo(set) (V)  
0.7525  
1.2  
1.5  
1.8  
2.5  
3.3  
5
Open  
22.46  
13.05  
9.024  
5.009  
3.122  
1.472