SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications below are examples. Specifications are subject
to change without notice. Tighter specifications available.
Please contact factory.
Supply Voltage VDD
Storage Temperature
-0.5 V to 7.0 V
-55OC to 125OC
Maximum Process Temperature 260OC for 20 seconds
Frequency Range1
Supply Voltage
Calibration Tolerance2
1 MHz to 160 MHz
+
_
1.8 V to 5.0 V 10%
ENABLE/DISABLE OPTIONS (E/N)
+_ 100 ppm
Statek offers two enable/disable options: E and N. The
E-version has a Tri-State output and stops oscillating
internally when the output is put into the high Z state.
The N-version does not have PIN 1 connected internally
and so has no enable/disable capability. The following
table describes the Enable/Disable option E.
Frequency Stability
Over Temperature3
+_ 100 ppm for Military
Supply Current (Typical)
24 MHz
+_ 50 ppm for Commercial
+_ 100 ppm for Industrial
1.8 V
3.3 V
5.0 V
1.5 mA
2.0 mA
3.0 mA
3.0 mA
5.0 mA
6.0 mA
8.0 mA
10.0 mA
13.0 mA
32 MHz
50 MHz
130 MHz
Output Load (CMOS)4
12.0 mA 23.0 mA 39.0 mA
ENABLE/DISABLE OPTION E
FUNCTION TABLE
15 pF
Start-up Time
5 ms MAX
Rise/Fall Time
Duty Cycle5
6 ns MAX
Enable (Pin 1 High*) Disable (Pin 1 Low)
40% MIN 60% MAX
10 ppm MAX
5,000 g, 0.3 ms, 1/2 sine
Output
Frequency Output
Oscillates
High Z State
Stops
Aging, first year
Shock, survival6
Vibration, survival7
Oscillator
Current
Normal
Very Low
20 g, 10-2,000 Hz swept sine
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
Operating Temp. Range -10OC to 70OC (Commerical)
-40OC to 85OC (Industrial)
-55OC to 125OC (Military)
PACKAGING OPTIONS
1. Not all frequencies available at all voltages. Contact factory.
2. Other tolerances available.
CXOX - Tray Pack
3. Does not include calibration tolerances. Other tolerances available.
4. Higher CMOS loads and TTL loads available. Contact factory.
5. 45/55 available upon request in most cases.
- 12 mm tape, 7” or 13” reels
Per EIA 481 (see Tape and Reel data sheet 10109)
6. Higher shock levels available. Contact factory.
7. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load.
HOW TO ORDER CXOX SURFACE MOUNT CRYSTAL OSCILLATORS
CXOX
4
S
N
SM3
40.0M , 100
/
100
/
/
I
Enable/Disable Terminations
Frequency
K = kHz
M = MHz
Supply Voltage
1 = 1.8 V
2 = 2.5 V
3 = 3.0 V
4 = 3.3 V
5 = 5.0 V
“S” if special or
custom design.
Blank if Std.
Calibration
Tolerance
@ 250C
Frequency
Stability over
Temp.Range
(in ppm)
Temp. Range:
C
= -10OC to +70OC
Option
E or N
Blank = SM1
= Gold Plated
I = -40OC to +85OC
(Lead Free)
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
(in ppm)
M = -55OC to +125OC
S
= Customer Specified
OR
/
/
200
/
I
Total
Temp. Range:
C
= -10OC to +70OC
Frequency
Tolerance
(in ppm)
I = -40OC to +85OC
M = -55OC to +125OC
S
= Customer Specified
Distribution:
10168 Rev A
E
■
■
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
■
■
■
Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
Pb
Änderungen vorbehalten / subject to change without notice
RSG [ RSG ELECTRONIC COMPONENTS GMBH ]
