SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications are typical at 25OC unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage VDD
Storage Temperature
-0.5 V to 7.0 V
-55OC to +125OC
Maximum Process Temperature 260OC for 20 seconds
Supply Voltage1
Calibration Tolerance2
5.0 V
+_ 100 ppm
ENABLE/DISABLE OPTIONS (E/T/N)
+
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the
T-version. So, the E-version offers very low current
consumption when the oscillator is disabled and the
T-version offers very fast output recovery when the
oscillator is re-enabled. The N-version does not have
PIN 1 connected internally and so has no enable/disable
capability. The following table summarizes the three
options.
_
Frequency Stability
Over Temperature3
50 ppm for Commercial
+_ 100 ppm for Industrial
+ 100 ppm for Military
_
Supply Current (Typical)
Output Load (CMOS)4
10 MHz 4 mA
24 MHz 8 mA
30 MHz 10 mA
40 MHz 12 mA
50 MHz 14 mA
15 pF
Start-up Time
Rise/Fall Time
5 ms MAX
6 ns MAX
Duty Cycle
40% MIN, 60% MAX
10 ppm MAX
3,000 g, 0.3 ms, 1/2 sine
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
Aging, first year
Shock, survival5
Vibration, survival6
E
T
20 g, 10-2,000 Hz swept sine
When enabled (PIN 1 is high*)
Operating Temp Ranges -10OC to +70OC (Commercial)
Output
Freq. output
Oscillates
Normal
Freq. output
Oscillates
Normal
-40OC to +85OC (Industrial)
-55OC to +125OC (Military)
Oscillator
1. Other voltages available. For 3.3 V, see CXO3M data sheet (10126). For others,
contact factory.
2. Other tolerances available.
3. Does not include calibration tolerance. Other tolerances available.
4. Higher CMOS loads and TTL loads available. Contact factory.
5. Higher shock version available. Contact factory about CXOMHG.
6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Current consumption
When disabled (PIN 1 is low)
Output
High Z state
Stops
High Z state
Oscillates
Oscillator
Current consumption
Very low
Lower than normal
Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load.
When re-enabled (PIN 1 changes from low to high)
Output recovery Delayed Immediate
PACKAGING OPTIONS
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
CXOM - Tray Pack
- 16mm tape, 7˝ or 13˝ reels
Per EIA 418 (see Tape and Reel data sheet 10109)
HOW TO ORDER CXOM SURFACE MOUNT CRYSTAL OSCILLATORS
CXOM
S
T
SM3
32.0M , 100
/
100
/
/
I
Terminations
Blank = SM1
= Gold Plated
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
Frequency
K = kHz
M = MHz
“S” if special or
custom design;
otherwise blank.
Calibration
Tolerance
@ 250C
Frequency
Stability over
Temp.Range
(in ppm)
Enable/Disable Option
E, T, or N
Temp. Range:
C
I
= -10OC to +70OC
= -40OC to +85OC
M = -55OC to +125OC
(in ppm)
S
= Customer Specified
OR
/
/
200
/
I
Total
Temp. Range:
C
= -10OC to +70OC
= -40OC to +85OC
Frequency
Tolerance
(in ppm)
I
M = -55OC to +125OC
S
= Customer Specified
Distribution:
10116 Rev E
E
■
■
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
■
■
■
Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de
Änderungen vorbehalten / subject to change without notice