Specifications are typical at 25OC unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage VDD
Storage Temperature
-0.3 V to 7.0 V
-55OC to 125OC
Maximum Process Temperature 260OC, 20 seconds
Supply Voltage1
3.3 V 10%
5.0 V 10%
ENABLE/DISABLE OPTIONS (E/T/N)
Calibration Tolerance
50ppm, or tighter as required
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the T-version.
So, the E-version offers very low current consumption
when the oscillator is disabled and the T-version offers very
fast output recovery when the oscillator is re-enabled. The
N-version does not have PIN 1 connected internally and so
has no enable/disable capability. The following table
summarizes the three options.
Frequency Stability
Over Temperature
100 ppm for 25OC to 150OC
150 ppm for 25OC to 175OC
175 ppm for 25OC to 200OC
Total Tolerance2
200 ppm for 25OC to 200OC
Supply Current (Typical)
3.3 V
5.0 V
24 MHz
32 MHz
50 MHz
3.0 mA
5.0 mA
6.0 mA
8.0 mA
10.0 mA
14.0 mA
39.0 mA
120 MHz 23.0 mA
Output Load (CMOS)
Start-up Time
15 pF
5 ms MAX
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
Rise/Fall Time
Duty Cycle
6 ns MAX
E
T
40% MIN, 60% MAX
10 ppm MAX at 25OC
100 ppm MAX at 200OC
Std: 3,000 g, 0.3 ms, 1/2 sine
HG: 10,000 g, 0.3 ms, 1/2 sine
20 g, 10-2,000 Hz swept sine
When enabled (PIN 1 is high*)
Aging, first year
Aging, 1,000 Hrs
Shock, survival3
Output
Freq. output
Oscillates
Normal
Freq. output
Oscillates
Normal
Oscillator
Current consumption
When disabled (PIN 1 is low)
Output
Vibration, survival4
Operating Temp Range -55OC up to 200OC
High Z state
Stops
High Z state
Oscillates
1. All frequencies, voltages, temperature ranges and enable/disable options may not be
available. Contact factory.
Oscillator
2. Total Tolerance = Calibration Tolerance + Frequency Stability over temperature.
3. For non-high-shock CXOHT and CXOMHT oscillators only. The specification for
CXOXHT oscillators is 5,000 g, 0.3 ms, /2 sine.
4. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing available.
Current consumption
Very low
Lower than normal
1
When re-enabled (PIN 1 changes from low to high)
Output recovery Delayed Immediate
Note: All parameters are measured at ambient temperature with a 10 M!, 15 pF load.
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
PACKAGING OPTIONS
CXOHT, CXOMHT, CXOXHT - Tray Pack
- 16 mm tape, 7” or 13” reels
Per EIA 481 (see Tape and Reel data sheet # 10109)
HOW TO ORDER CXOHT, CXOMHT and CXOXHT OSCILLATORS
CXOMHT
4
S
E
SM3
20.0M,
/
/ 200
/
H
CXOHT
CXOMHT
CXOXHT
Total Frequency
Tolerance (in
ppm)
Temp. Range:
H = 250C to 2000C
S = Customer
Specified Temp.
Range
“S” if special or
custom design.
Blank if Std.
Enable/Disable
Option E or T
or N
Frequency
M = MHz
K = kHz
Calibration
Tolerance
@ 250C
Terminations
Blank = SM1
= Gold Plated
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
(in ppm)
Supply Voltage
4 = 3.3 V
5 = 5.0 V
HG = High Shock
otherwise leave
blank.
Frequency
Stability over
Temp. Range
(in ppm)
OR
25
/
175
/
/
H
Frequency
Calibration
Tolerance
@ 250C
Total
Frequency
Tolerance
(in ppm)
Temp. Range:
H = 250C to
2000C
S = Customer
Specified Temp.
Range
Stability over
Temp. Range
(in ppm)
(in ppm)
Distribution:
■
■
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
■
■
■
Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de
Änderungen vorbehalten / subject to change without notice
RSG [ RSG ELECTRONIC COMPONENTS GMBH ]
