9000 Series / Molded SIP Reed Relays
2
2
2
Model Number
Parameters
9001
9002
9091
Test Conditions
Units
4 Pin SIP
6 Pin SIP
1 Form A
COIL SPECS.
5
12
5
12
6.5 15.0
350 750
3.75 9.0
0.4 1.0
5
12
Nom. Coil Voltage
Max. Coil Voltage
Coil Resistance
Operate Voltage
Release Voltage
VDC
VDC
Ω
6.5 15.0
6.5 15.0
500 1000
500 1000
+/- 10%, 25° C
Must Operate by
Must Release by
3.75
0.4
9.0
1.0
3.75
0.4
9.0
1.0
VDC - Max.
VDC - Min.
CONTACT RATINGS
Switching Voltage
Switching Current
Carry Current
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Volts
Amps
200
0.5
1.5
10
200
0.5
1.5
200
0.5
1.5
10
Amps
Contact Rating
Watts
x 106 Ops.
10
Life Expectancy-Typical1
Static Contact
Signal Level 1.0V, 1.0mA
1000
1000
500
50mV, 10mA
Ω
Ω
Resistance (max. init.)
0.150
0.200
0.150
0.200
0.125
0.150
Dynamic Contact
Resistance (max. init.)
0.5V, 50mA
at 100 Hz, 1.5 msec
RELAY SPECIFICATIONS
Insulation Resistance
(minimum)
Between all Isolated Pins
at 100V, 25°C, 40% RH
No Shield
x 1012
x 1012
x 1012
Ω
Capacitance - Typical
Across Open Contacts
pF
pF
pF
0.7
-
-
-
0.8
0.1
0.1
-
-
Shield Floating
Shield Guarding
Open Contact to Coil
No Shield
Shield Floating
Shield Guarding
pF
pF
pF
1.4
-
-
-
1.4
0.5
2.0
-
-
Contact to Shield
Contacts Open, Shield
Floating
pF
-
1.4
-
Dielectric Strength
(minimum)
Between Contacts
Contacts to Shield
Contacts/Shield to Coil
VDC/peak AC
VDC/peak AC
VDC/peak AC
300
-
1500
300
1500
1500
200
-
1500
Operate Time - including
bounce - Typical
At Nominal Coil Voltage,
30 Hz Square Wave
msec.
msec.
0.35
0.35
0.50
Zener-Diode Suppression4
Diode Suppression
0.10
-
0.10
-
0.30
0.12
Release Time - Typical
Top View:
Dot stamped
on relay refers
to pin #1
Grid = .1"x.1"
(2.54mm x 2.54mm)
Note s:
1Consult factory for life expectancy at other switching
loads. 9090 series contact resistance >0.5W defines
end of life or failure to open.
2Optional diode is connected to pin #2 (+) and pin #3(-).
Correct coil polarity must be observed.
Environmenta l Ra tings
Storage Temp: 35°C to 100°C; Operating Temp: 20°C to 85°C
Solder Temp: 270°C max; 10 sec. max
The operate and release voltage and the coil resistance are
specified at 25°C. These values vary by approximately
0.4%/°C as the ambient temperature varies.
-
+
-
+
39000 series part numbers designated with Form B
contacts, these relays contain bias magnets.
Correct coil polarity must be observed.
4Consists of 20V Zener-diode and 1N1002 diode
in series, connected in parallel with coil.
Vibration: 20 G’s to 2000 Hz; Shock: 50 G’s
COTO TECHNOLOGY R H O P O IN T C O M P O N E N T S L T D Holland Rd, Hurst Green, Oxted, Surrey, RH8 9AX,ENGLAND
RHOPOINT [ RHOPOINT COMPONENTS ]
