欢迎访问ic37.com |
会员登录 免费注册
发布采购

R5-434-5-50 参数 Datasheet PDF下载

R5-434-5-50图片预览
型号: R5-434-5-50
PDF下载: 下载PDF文件 查看货源
内容描述: FM无线发射和接收器模块 [FM Radio Transmitter & Receiver Modules]
分类和应用: 无线
文件页数/大小: 8 页 / 117 K
品牌: RFSOLUTIONS [ RFSOLUTIONS.LTD ]
 浏览型号R5-434-5-50的Datasheet PDF文件第1页浏览型号R5-434-5-50的Datasheet PDF文件第3页浏览型号R5-434-5-50的Datasheet PDF文件第4页浏览型号R5-434-5-50的Datasheet PDF文件第5页浏览型号R5-434-5-50的Datasheet PDF文件第6页浏览型号R5-434-5-50的Datasheet PDF文件第7页浏览型号R5-434-5-50的Datasheet PDF文件第8页  
FM Radio Transmitter & Receiver Modules  
T5 / R5  
Connection Diagram  
T5  
R 5  
1
2
3
4
5
1
2
3 4 5 6 7  
Figure 1: Transmitter  
Figure 2: Receiver  
Pin Descriptions:  
RF GND (pin 1)  
RF ground pin, internally connected to pin 4 (0V).  
This pin should ideally be connected to the  
nearest ground plane (e.g. coax braid, main PCB  
ground plane etc.)  
RF IN (pin 1)  
50RF input from antenna, connect using  
shortest possible route. This input is isolated from  
the internal circuit using the air gap of the front  
end SAW RF filter  
RF GND (pin 2)  
RF ground connection, preferable connected to a  
solid plane.  
RF OUT (pin2)  
50RF antenna output. To achieve best results  
the antenna impedance must match that of the  
module.  
RSSI (pin 3)  
The Received Signal Strength Indicator provides a  
DC output voltage proportional to the RF input  
signal. The amplitude of the RSSI voltage  
increases with increasing RF signal strength.  
V
CC (pin 3)  
+Ve supply pin (3.0 to 9.0 volts). The module will  
generate RF when VCC is present. It is strongly  
recommended that a 100nF capacitor decouples  
the supply rail as close as possible to this pin.  
GND (pin 4)  
Connect to power supply ground.  
GND (pin 4)  
Supply and data ground connection, connected to  
pin 1.  
V
CC (pin 5)  
+Ve supply pin. Operation from a 5V supply able  
to source6mA at less than Vp-p ripple.  
Data IN (pin 5)  
This input has an impedance of 47Kand should  
ideally be driven by a CMOS logic drive or  
compatible. The drive circuitry should be supplied  
with the same supply voltage as the Tx module.  
AF (pin 6)  
Audio frequency output.  
DATA OUT (pin 7)  
CMOS compatible output. This may be used to  
drive external decoders. To reduce any noise on  
this output ass a Add a 56pF cap from this pin to  
GND.  
Ordering Information:  
Part No  
Description  
Tx 433.92MHz 9v 20Kbps  
Tx 433.92MHz 5v 128Kbps  
Part No  
Description  
T5-434-9-20  
T5-434-5V  
R5-434-5-20  
Rx 433.92MHz 20Kbps  
R5-434-5-20B Rx 433.92MHz 20Kbps ‘B part’  
R5-434-5-50 Rx 433.92MHz 5V 50Kbps  
R5-434-5-50B Rx 433.92MHz 5V 50Kbps ‘B part’  
T5-434-5-20B Tx 433.92MHz 5v 20Kbps ‘B part’  
T5-434-3V Tx 433.92MHz 3v 50Kbps  
T5-434-3-20B Tx 433.92MHz 3v 20Kbps ‘B part’  
R5-434-5-128  
Rx 433.92MHz 5V 128Kbps  
DS305-8  
Nov ‘05  
©2005 REG No 277 4001, England.  
Page 2