®
SF2038B-2
•
•
•
•
•
Designed for SDARS IF Receiver
Low Insertion Loss
5.0 X 7.0 mm Surface-Mount Case
Differential or Single Ended Input and Output
Complies with Directive 2002/95/EC (RoHS)
76.500 MHz
SAW Filter
Pb
Absolute Maximum Ratings
Rating
Value
+10
Units
dBm
VDC
°C
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range (with tape & reel)
Storage Temperature Range (without tape & reel)
Max Soldering Profile
30
-40 to +85
-50 to +125
°C
265°C for 10 s
SMP-03
Electrical Characteristics
Characteristic
Sym
Notes
Min
Typ
Max
Units
Nominal Center Frequency
f
76.500
10.0
14.0
16.8
18.0
0.70
40
MHz
C
1
Passband
Insertion Loss
IL
12.0
dB
1dB Passband
15dB Bandwidth
30dB Bandwidth
BW
12.5
MHz
MHz
MHz
1
BW
BW
18.0
19.2
1.3
15
30
1
Amplitude Ripple over fc ±6.25 MHz
Group Delay Variation over fc ±6.25 MHz
50 to 64.44 MHz
dB
P-P
P-P
GDV
150
ns
Rejection
40
36
46
64.44 to 66.70 MHz
64.44 to 66.70 MHz
-40 to 85°C
85 to 105°C
41
30
1, 3
1
dB
86.30 to 87.54 MHz
87.54 to 91.50 MHz
91.50 to 100 MHz
*30
31
44
44
47
40
Operating Temperature Range
Frequency Coeffieient
Differential Input
T
-40
+105
°C
A
FTC
-87
ppm/°C
175 ohms
180 ohms
Differential Output
Case Style
SMP-03 7 x 5 mm Nominal Footprint
RFM SF2038B YYWWS
6
Lid Symbolization (YY=year, WW=week, S=shift) See note 4
*At low temperature extreme -40°C
Notes:
1.
Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to
50 W and measured with 50 W network analyzer.
2.
3.
Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
4.
5.
6.
7.
"LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
The design, manufacturing process, and specifications of this filter are subject to change.
Tape and Reel Standard ANSI / EIA 481.
Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that
the filter must always be installed in one direction per the circuit design.
8.
9.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
10. ©Copyright 1999, RF Monolithics Inc.
11. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc.
RFM Europe
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com
http://www.rfm.com
SF2038B-2-022607
Page 1
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
RFM [ RF MONOLITHICS, INC ]
