May 2005
ASM2I9942P
rev 0.3
Power Consumption of the ASM2I9942P and
Thermal Management
per output, (Μ)ΣCL represents the external capacitive
output load, N is the number of active outputs (N is
always 12 in case of the ASM2I9942P). The
ASM2I9942P supports driving transmission lines to
maintain high signal integrity and tight timing parameters.
Any transmission line will hide the lumped capacitive load
at the end of the board trace, therefore, ΣCL is zero for
controlled transmission line systems and can be
eliminated from equation 1. Using parallel termination
output termination results in equation 2 for power
dissipation.
The ASM2I9942P AC specification is guaranteed for the
entire operating frequency range up to 250MHz. The
ASM2I9942P power consumption and the associated
long-term reliability may decrease the maximum
frequency limit, depending on operating conditions such
as clock frequency, supply voltage, output loading,
ambient temperature, vertical convection and thermal
conductivity of package and board. This section
describes the impact of these parameters on the junction
temperature and gives a guideline to estimate the
ASM2I9942P die junction temperature and the associated
device reliability.
In equation 2, P stands for the number of outputs with a
parallel or thevenin termination, VOL, IOL, VOH and IOH are
a function of the output termination technique and DCQ is
the clock signal duty cycle. If transmission lines are used
ΣCL is zero in equation 2 and can be eliminated. In
general, the use of controlled transmission line
techniques eliminates the impact of the lumped capacitive
loads at the end lines and greatly reduces the power
dissipation of the device. Equation 3 describes the die
junction temperature TJ as a function of the power
consumption.
Table 8. Die junction temperature and MTBF
Junction temperature
MTBF (Years)
(°C)
100
110
120
130
20.4
9.1
4.2
2.0
Where Rthja is the thermal impedance of the package
(junction to ambient) and TA is the ambient temperature.
According to Table 8, the junction temperature can be
used to estimate the long-term device reliability. Further,
combining equation 1 and equation 2 results in a
maximum operating frequency for the ASM2I9942P in a
series terminated transmission line system, equation 4.
Increased power consumption will increase the die
junction temperature and impact the device reliability
(MTBF). According to the system-defined tolerable
MTBF, the die junction temperature of the ASM2I9942P
needs to be controlled and the thermal impedance of the
board/package should be optimized.The power dissipated
in the ASM2I9942P is represented in equation 1.
Where ICCQ is the static current consumption of the
ASM2I9942P, CPD is the power dissipation capacitance
P
= ICCQ + VCC ⋅ fCLOCK ⋅ N ⋅ C
+
C
⋅VCC
Equation1
L
∑
TOT
PD
M
P
=VCC ⋅ ICCQ + VCC ⋅ fCLOCK ⋅ N ⋅ C
+
C
+
[
∑
P
DC ⋅ I
(
VCC −VOH
)
+
(
1− DCQ
)
⋅ IOL ⋅VOL
]
Equation 2
Equation 3
L
∑
TOT
PD
Q
OH
M
TJ = TA + P ⋅ Rthja
TOT
TJMAX − TA
1
(
)
fCLOCKMAX
=
⋅
− ICCQ ⋅VCC
Equation 4
CPD ⋅ N ⋅VC2C
Rthja
Low Voltage 1:18 Clock Distribution Chip
5 of 10
Notice: The information in this document is subject to change without notice.
PULSECORE [ PulseCore Semiconductor ]
