欢迎访问ic37.com |
会员登录 免费注册
发布采购

ASM1834S 参数 Datasheet PDF下载

ASM1834S图片预览
型号: ASM1834S
PDF下载: 下载PDF文件 查看货源
内容描述: 双5V和3.3V微处理器电源监控器,带有手动复位 [Dual 5V and 3.3V μP Power Supply Supervisor with Manual Reset]
分类和应用: 微处理器监控
文件页数/大小: 10 页 / 261 K
品牌: PULSECORE [ PulseCore Semiconductor ]
 浏览型号ASM1834S的Datasheet PDF文件第1页浏览型号ASM1834S的Datasheet PDF文件第2页浏览型号ASM1834S的Datasheet PDF文件第3页浏览型号ASM1834S的Datasheet PDF文件第5页浏览型号ASM1834S的Datasheet PDF文件第6页浏览型号ASM1834S的Datasheet PDF文件第7页浏览型号ASM1834S的Datasheet PDF文件第8页浏览型号ASM1834S的Datasheet PDF文件第9页  
November 2006  
rev 1.5  
ASM1834/A/D  
Manual Reset Operation  
Reset Output Signal  
Push-button switch input, PBRST, allows the user to override  
the internal trip point detection circuits and issue reset  
signals. The pushbutton input is debounced and is pulled  
HIGH through an internal 40kresistor.  
Reset output signals are valid as long as either voltage at  
5VIN or 3.3VIN is above 1.2V. In addition, the ASM1834 has  
push-pull outputs that can remain valid below a 1.2V input  
level. To sink current below 1.2V, a resistor should be  
connected from the RESET output to ground. This resistor  
guarantees a valid reset signal down to 0V. A 100kvalue is  
suggested.  
When at least one of the reset outputs is not asserted, a push  
button initiated reset signal can be issued by holding PBRST  
LOW for at least 2ms. When PBRST is held LOW, both resets  
become active and remain active for approximately 350ms  
after PBRST returns HIGH. (See figures 3 and 4).  
The AS1834A open drain reset outputs require pull-up  
resistors and must be low enough in value to pull the output  
into a HIGH state. Resistor value is not critical in most  
applications and a value of 10kis suggested. (See Figures  
5 and 6).  
3.3V  
5V  
ASM1834  
The ASM1834A open drain reset outputs can be connected  
to the same potential through a single pull-up resistor. In this  
configuration a failure on either supply will generate an active  
LOW reset. If the inputs are pulled-up to different voltages,  
the reset outputs (pin 2 and pin 7) cannot be connected to  
form a wired “AND” (see figure 7).  
8
1
3.3VIN  
5VIN  
7
6
5
2
5V RESET 3.3V RESET  
3
4
5VTOL  
GND  
3.3VTOL  
PBRST  
µP  
Input  
RESET  
Figure 3: Pushbutton Reset  
PBRST  
100kΩ  
t
PB  
Figure 5: ASM1834 RESET Valid to 0V  
V
IH  
t
PDLY  
V
IL  
3.3V  
5V  
t
ASM1834  
RST  
8
1
3.3VIN  
5VIN  
RESET  
RESET  
10kΩ  
VOH  
VOL  
10kΩ  
7
6
5
2
5V RESET 3.3V RESET  
3
4
5VTOL  
GND  
3.3VTOL  
PBRST  
Figure 4: Timing Diagram: Pushbutton Reset  
Figure 6: ASM1834A Open Drain Output Pull-Up Resistor  
4 of 10  
Dual 5V and 3.3V µP Power Supply Supervisor with Manual Reset  
Notice: The information in this document is subject to change without notice