DPA422-426
LINE-SENSE (L) Pin Operation
those that control the on/off states of the output such as UV, OV
and remote ON/OFF, the vertical axis represents the enable/
disable states of the output. UV triggers at IUV (+50 µA typical
with 4 µA hysteresis) and OV triggers at IOV (+135 µA typical with
4 µA hysteresis). Between the UV and OV thresholds, the
output is enabled. For line feed-forward with DCMAX reduction,
the vertical axis represents the magnitude of the DCMAX Line
feed-forward with DCMAX reduction lowers maximum duty cycle
from 75% at IL(DC) (+55 µA typical) to 33% at IOV (+135 µA).
When current is fed into the LINE-SENSE pin, it works as a
voltage source of approximately 2.6 V up to a maximum current
of +240 µA (typical). At +240 µA, this pin turns into a constant
current sink. Refer to Figure 8. In addition, a comparator with a
threshold of 1 V is connected at the pin and is used to detect
when the pin is shorted to the SOURCE pin.
There are a total of five functions available through the use of
the LINE-SENSE pin: OV, UV, line feed-forward with DCMAX
reduction, remote ON/OFF and synchronization. Shorting the
LINE-SENSE pin to the SOURCE pin disables all five functions.
The LINE-SENSE pin is typically used for line sensing by
connecting a resistor from this pin to the positive input DC
voltage bus to implement OV, UV and line feed-forward with
DCMAX reduction over line voltage. In this mode, the value of the
resistor determines the line OV/UV thresholds, and the DCMAX is
reduced linearly with input DC high-voltage starting from just
above the UV threshold. This pin can also be used as the input
pin for remote ON/OFF and synchronization. An external
transistor placed between the LINE-SENSE pin and the
CONTROL pin realizes remote ON/OFF via UV or OV threshold.
Synchronization is available by connecting an open drain
external MOSFET between the LINE-SENSE pin and the
SOURCE pin to generate synchronization pulse. Each time the
MOSFET turns on, the falling edge of the LINE-SENSE pin
voltage initiates a new switching cycle. The lowest
synchronization frequency guaranteed by DPA-Switch is
128 kHz. Refer to Table 2 for possible combinations of the
functions with example circuits shown in Figure 11 through
Figure 24. A description of specific functions in terms of the
LINE-SENSE pin I/V characteristic is shown in Figure 7 (right
hand side). The horizontal axis represents LINE-SENSE pin
current with positive polarity indicating currents flowing into the
pin. The meaning of the vertical axes varies with functions. For
EXTERNAL CURRENT LIMIT (X) Pin Operation
When current is drawn out of the EXTERNAL CURRENT LIMIT pin,
it works as a voltage source of approximately 1.3 V up to a
maximum current of -230 µA (typical). At -230 µA, it turns into a
constant current source (refer to Figure 8).
There are two functions available through the use of the
EXTERNAL CURRENT LIMIT pin: external current limit and
remote ON/OFF. Shorting the EXTERNAL CURRENT LIMIT pin
and SOURCE pin disables both functions. In high efficiency
applications, this pin can be used to reduce the current limit
externally to a value close to the operating peak current, by
connecting the pin to the SOURCE pin through a resistor. The
pin can also be used as a remote ON/OFF control input.
Table 2 shows several different ways of using this pin. See
Figure 7 for a description of the functions where the horizontal
axis (left hand side) represents the EXTERNAL CURRENT LIMIT
pin current. The meaning of the vertical axes varies with
function. For those that control the on/off states of the output
such as remote ON/OFF, the vertical axis represents the enable/
disable states of the output. For external current limit, the
vertical axis represents the magnitude of the ILIMIT. Please see
graphs in the Typical Performance Characteristics section for
the current limit programming range and the selection of the
appropriate resistor value.
9
www.powerint.com
Rev. T 12/12
POWERINT [ Power Integrations ]
