PI74LPT16373
3.3V 16-Bit Transparent Latch
Capacitance (TA = 25°C, f = 1 MHz)
(1)
Parameters
Description
Test Conditions
= 0V
Typ
4.5
Max.
Units
C
IN
Input Capacitance
Output Capacitance
V
V
6
8
IN
pF
COUT
= 0V
5.5
OUT
Note:
1. This parameter is determined by device characterization but is not production tested.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 2.7V to 3.6V)
(1)
(2)
Parameters
Description
Test Conditions
Min.
2.2
Typ
Max. Units
Input HIGH Voltage (Input pins)
Input HIGH Voltage (I/O pins)
—
—
5.5
V
V
Guaranteed Logic HIGH Level
IH
IL
2.0
5.5
V
Input LOW Voltage
(Input and I/O pins)
Guaranteed Logic LOW Level
–0.5
—
0.8
Input HIGH Current (Input pins)
Input HIGH Current (I/O pins)
Input LOW Current (Input pins)
Input LOW Current (I/O pins)
High Impedance Output Current
(3-State Output pins)
V
V
V
V
V
V
= 5.5V
—
—
—
—
—
—
—
—
—
±1
±1
V
V
V
V
V
V
= Max.
= Max.
= Max.
= Max.
= Max.
= Max.
IN
IN
IN
IN
CC
CC
CC
CC
CC
CC
I
I
IH
= V
CC
= GND
= GND
= 5.5V
—
±1
µA
±1
IL
—
I
I
—
±1
±1
OZH
OZL
OUT
OUT
= GND
—
V
Clamp Diode Voltage
VCC = Min., I = –18mA
–0.7
–1.2
V
IK
IN
V
= 3.3V, V = V or V ,
IN IH IL
CC
I
I
Output HIGH Current
Output LOW Current
–36
50
–60
90
–110
ODH
(3)
V = 1.5V
O
mA
V
= 3.3V, V = V or V ,
IN IH IL
CC
200
ODL
(3)
V = 1.5V
O
I
= –0.1 mA V -0.2
—
3.0
3.0
—
—
—
OL
OL
OL
OL
OL
OL
OL
CC
V
V
= Min.
CC
= V or V
I
I
I
I
I
I
= –3 mA
= –8 mA
= –24 mA
= 0.1 mA
= 16 mA
= 24 mA
2.4
IN
IH
IL
V
Output HIGH Voltage
Output LOW Voltage
OH
(5)
2.4
—
V
V
= 3.0V,
CC
= V or V
2.0
—
—
IN
IH
IL
V
—
0.2
0.4
0.5
–240
±100
—
V
V
= Min.
CC
VOL
= V or V
—
0.2
0.3
–85
—
IN
IH
IL
—
(4)
(3)
I
Short Circuit Current
–60
—
mA
µA
V
V
= Max. , V
= GND
OS
CC
CC
OUT
I
Power Down Disable
Input Hysteresis
= 0V, V or V
≤ 4.5V
OUT
OFF
IN
V
—
150
mV
H
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V = 3.3V, +25°C ambient and maximum loading.
CC
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. This parameter is guaranteed but not tested.
5.
V
= V – 0.6V at rated current.
OH CC
PS2069C
10/05/04
3
PERKINELMER [ PERKINELMER OPTOELECTRONICS ]
