PE175BF and PE175BUV
Operational Specifications
Physical Specifications
Description
Power
Nominal
Range
Description
Arc Gap
Specification
175 watts
150-200 watts
12-16 amps (DC)
11-14 volts (DC)
.045 inch (1.14mm)
2
Current
14 amps (DC)
12.5 volts (DC)
Reflector Geometry
Weight
Parabolic Y = 0.5 X (inch)
Operating Voltage
Ignition Voltage
Temperature
Lifetime*
131 grams
23 kilovolts (recommended minimum)
150º C (maximum)
Window Diameter
1 inch (25.4 mm)
1000 hours (500 hour warranty)
Focused Output at F/1.0 Lens
* End of lamp life is defined as 50% of initial output.
Description
6mm aperture
8mm aperture
Visible Output
1400 Lumens
830 Lumens
Total Output*
13 watts
7.8 watts
Output at Nominal Power
F= UV Filtered Output/ UV = UV Enhanced Output
* Nominal values at 175 watts after 2 hour burn-in.
Description
Peak Intensity
Radiant Output*
UV Output*
PE175BF
PE175BUV
3
3
350x10 candelas
330x10 candelas
Notes
25 watts
25 watts
3.5 watts
13 watts
2000 Lumens
5050 Kelvin
4%
1. Lamp must not be operated with window facing upwards within
1.2 watts
14 watts
45º of vertical.
IR Output*
2. Seal temperature must not exceed 150º C.
Visible Output*
2200 Lumens
3. Current/power regulated power supplies and PerkinElmer lamp
Color Temperature 5600 Kelvin
Peak Instabilities
4%
housing units are recommended.
4. Lamp must be operated within recommended current and power
range. Over powering may lead to arc instability, hard starting
and premature aging.
Beam Geometry** 4.5º/5º/6º
4.5º/5º/6º
*These values indicate total output in all directions.
5. Hot mirror assembly is available for IR filtering.
Wavelengths = UV<390nm, IR>770nm, Visible 390nm to 770nm.
6. CERMAX lamps are much safer lamps to use than their quartz
xenon arc lamp equivalents. However, caution must be practiced
when operating lamps because they are under high pressure,
require high voltage, reach temperatures up to 200º C, and their
IR and UV radiation can cause skin burns and eye damage.
Read hazard sheet included with each lamp shipment.
** Beam Geometry defined as half angle at 10% PTS after 01/100/1000 hours.
Dimensions
1.00
.250 (6.35)
(25.4)
1.000 (25.4)
Spectral Output
.250 (6.35)
.164
(4.19)
F
UV
F + HOT MIRROR
100
80
6-32 UNC 2B x .156 DP
2 x .40
3 Holes EQ SP on A
(10.2)
.035
(.899)
.750 (19.05) BC
1.667
60
40
1.298 (32.96)
42.34
.066 (1.52)
.125 (3.18)
Y
X
20
0
Focal Point
Cathode
200
300
400
500
600
700
800
900
1000 1100
WAVELENGTH (NM)
Dimensions in parentheses are in millimeters.
PerkinElmer welcomes inquiries about special lamps. We would be pleased to discuss the requirements of your application and the feasibility of
designing a lamp specifically suited to your needs.
For more information e-mail us at opto@perkinelmer.com or visit our web site at www.perkinelmer.com/opto.
All values are nominal; specifications subject to change without notice.
USA:
Europe:
Asia:
PerkinElmer Optoelectronics
44370 Christy St.
Fremont, CA 94538
Phone: (510) 979-6500
Fax: (510) 687-1140
Toll Free: (800) 775-6786
PerkinElmer Optoelectronics GmbH
Wenzel-Jaksch-Str. 31
65199 Wiesbaden
Germany
Phone: +49 611 492 0
Fax: +49 611 492 369
PerkinElmer Optoelectronics
47 Ayer Rajah Crescent #06-12
Singapore 139947
Phone: +65 775 2022
Fax: +65 775 1008
.
© 2000 PerkinElmer inc. All rights reserved.
DS-155 Rev C 1101
www.perkinelmer.com/opto
PERKINELMER [ PERKINELMER OPTOELECTRONICS ]
