PE125BF and PE125BUV
Operational Specifications
Physical Specifications
Description
Power
Nominal
Range
Description
Arc Gap
Specification
125 watts
75-150 watts
7-14 amps (DC)
9.5-12.5 volts (DC)
.044 inch (1.14mm)
Parabolic Y2 = 0.5 X (inch)
130.8 grams
Current
12 amps (DC)
Reflector Geometry
Weight
Operating Voltage 11 volts (DC)
17 kilovolts (recommended minimum)
150ºÞ C (maximum)
1000 hours (500 hour warranty)
Ignition Voltage
Temperature
Lifetime*
Window Diameter
1 inch (25.4 mm)
Focused Output at F/1.0 Lens
* End of lamp life is defined as 50% of initial output.
Description
6mm aperture
8mm aperture
Visible Output
Total Output*
9.5 watts
1050 Lumens
620 Lumens
Output at Nominal Power
5.6 watts
F= UV Filtered Output/ UV = UV Enhanced Output
* Nominal values at 125 watts after 2 hour burn-in.
Description
PE125BF
300x103 candelas
17 watts
PE125BUV
280x103 candelas
17 watts
Peak Intensity
Radiant Output*
UV Output*
Notes
1. Lamp must not be operated with window facing upwards within
0.8 watts
2.2 watts
45º of vertical.
IR Output*
10 watts
9 watts
2. Seal temperature must not exceed 150º C.
Visible Output*
Color Temperature
Peak Instabilities
Beam Geometry**
1500 Lumens
5600 Kelvin
4%
1350 Lumens
5050 Kelvin
4%
3. Current/power regulated power supplies and PerkinElmer lamp
housing units are recommended.
4. Lamp must be operated within recommended current and power
range. Over powering may lead to arc instability, hard starting
and premature aging.
4.5º/5º/6º
4.5º/5º/6º
*These values indicate total output in all directions.
5. Hot mirror assembly is available for IR filtering.
Wavelengths = UV<390nm, IR>770nm, Visible 390nm to 770nm.
6. CERMAX lamps are much safer lamps to use than their quartz
xenon arc lamp equivalents. However, caution must be practiced
when operating lamps because they are under high pressure,
require high voltage, reach temperatures up to 200º C, and their
IR and UV radiation can cause skin burns and eye damage.
Read hazard sheet included with each lamp shipment.
** Beam Geometry defined as half angle at 10% PTS after 01/100/1000 hours.
Dimensions
1.00
.250 (6.35)
(25.4)
1.000 (25.4)
.250 (6.35)
Spectral Output
.164
(4.19)
F
UV
F + HOT MIRROR
100
80
6-32 UNC 2B x .156 DP
2 x .40
3 Holes EQ SP on A
(10.2)
.035
(.899)
.750 (19.05) BC
1.667
60
40
1.298 (32.96)
42.34
.066 (1.52)
.125 (3.18)
Y
X
20
0
200
300
400
500
600
700
800
900
1000 1100
Focal Point
Cathode
WAVELENGTH (NM)
PerkinElmer welcomes inquiries about special lamps. We would be pleased to discuss the requirements of your application and the feasibility of
designing a lamp specifically suited to your needs.
For more information e-mail us at opto@perkinelmer.com or visit our web site at www.perkinelmer.com/opto.
All values are nominal; specifications subject to change without notice.
USA:
Europe:
Asia:
PerkinElmer Optoelectronics
44370 Christy St.
Fremont, CA 94538
Phone: (510) 979-6500
Fax: (510) 687-1140
Toll Free: (800) 775-6786
PerkinElmer Optoelectronics GmbH
Wenzel-Jaksch-Str. 31
65199 Wiesbaden
Germany
Phone: +49 611 492 0
Fax: +49 611 492 369
PerkinElmer Optoelectronics
47 Ayer Rajah Crescent #06-12
Singapore 139947
Phone: +65 775 2022
Fax: +65 775 1008
.
DS-152 Rev C 1101
© 2000 PerkinElmer inc. All rights reserved.
www.perkinelmer.com/opto
PERKINELMER [ PERKINELMER OPTOELECTRONICS ]
