PE125B-10F and PE125B-10UV
Operational Specifications
Physical Specifications
Description
Power
Nominal
Range
Description
Arc Gap
Specification
125 watts
75-150 watts
7-14 amps (DC)
10-12.5 volts (DC)
.038 inch (0.96mm)
2
2
2
2
Current
11.5 amps (DC)
11 volts (DC)
Reflector Geometry
Weight
Ellipsoidal 1= X /M +Y /N
150 grams
Operating Voltage
Ignition Voltage
Temperature
Lifetime*
23 kilovolts (recommended minimum)
150º C (maximum)
Window Diameter
1 inch (25.4 mm)
1000 hours (500 hour warranty)
Focused Output
* End of lamp life is defined as 50% of initial output.
Description
Visible Output*
Total Output
11 watts
6mm aperture
3mm aperture
1250 Lumens
650 Lumens
Output at Nominal Power
6.4 watts
F= UV Filtered Output/ UV = UV Enhanced Output
* Nominal values at 125 watts after 2 hour burn-in
Description
PE125B-10F
18.5 watts
1.1 watts
PE125B-10UV
18.5 watts
Radiant Output*
UV Output*
Notes
2.7 watts
1. Lamp must not be operated with window facing upwards within
IR Output*
10.3 watts
1570 Lumens
5900 Kelvin
4%
9.7 watts
45º of vertical.
Visible Output*
Color Temperature
Peak Instabilities
1400 Lumens
5050 Kelvin
4%
2. Seal temperature must not exceed 150º C.
3. Current/power regulated power supplies and PerkinElmer lamp
housing units are recommended.
Spot Size at Crossover .09” at 50% pts
Spot Size at Crossover .23” at 10% pts
*These values indicate total output in all directions.
4. Lamp must be operated within recommended current and power
range. Over powering may lead to arc instability, hard starting
and premature aging.
0.9” at 50% pts
.23” at 10% pts
5. Hot mirror assembly is available for IR filtering.
Wavelengths = UV<390nm, IR>770nm, Visible 390nm to 770nm.
6. CERMAX lamps are much safer lamps to use than their quartz
xenon arc lamp equivalents. However, caution must be practiced
when operating lamps because they are under high pressure,
require high voltage, reach temperatures up to 200º C, and their
IR and UV radiation can cause skin burns and eye damage.
Read hazard sheet included with each lamp shipment.
** Beam Geometry defined as half angle at 10% PTS after 01/100/1000 hours.
Dimensions
1.00
(25.4)
.250 (6.35)
1.00
.55 (13.97)
(25.4)
.25 (6.35)
Spectral Output
.165
(4.19)
F
UV
F + HOT MIRROR
100
80
6-32 UNC 2B x .156 DP
3 Holes EQ SP on A
.750 (19.05) BC
2 x .40 (10.2)
.035 (.899)
1.298
(32.97)
2.167 (55.04)
60
40
.866 (21.99)
.008 (.203)
M=1.059
N=0.50
.126 (3.2)
20
0
Focal Point
Cathode
Reflector Edge
C
Ellipse
L
200
300
400
500
600
700
800
900
1000 1100
WAVELENGTH (NM)
Dimensions in parentheses are in millimeters.
PerkinElmer welcomes inquiries about special lamps. We would be pleased to discuss the requirements of your application and the feasibility of
designing a lamp specifically suited to your needs.
For more information e-mail us at opto@perkinelmer.com or visit our web site at www.perkinelmer.com/opto.
All values are nominal; specifications subject to change without notice.
USA:
Europe:
Asia:
PerkinElmer Optoelectronics
44370 Christy St.
Fremont, CA 94538
Phone: (510) 979-6500
Fax: (510) 687-1140
Toll Free: (800) 775-6786
PerkinElmer Optoelectronics
GmbH
Wenzel-Jaksch-Str. 31
65199 Wiesbaden
Germany
PerkinElmer Optoelectronics
47 Ayer Rajah Crescent #06-12
Singapore 139947
Phone: +65 775 2022
Fax: +65 775 1008
.
Phone: +49 611 492 0
Fax: +49 611 492 369
© 2000 PerkinElmer inc. All rights reserved.
DS-162 Rev C 1101
www.perkinelmer.com/opto
PERKINELMER [ PERKINELMER OPTOELECTRONICS ]
