OXCFU950 OVERVIEW
OXFORD SEMICONDUCTOR, INC.
PIN DESCRIPTIONS
Pin Number
Pad TypeNote 1
Pin Name
Description
PC Card/Compact Flash Interface & ControlNote 2
14,16,17,18,21,22,23,
25,29,31, 34
13,11,9,46,44,42,40,38 B_T_33_5_N_2_ D[15:0]
,10,8,6,45,43,41,39,37
I_C_33_5_N_
A[10:0]
PC Card/CompactFlash address bus, bits [10:0]
PC Card/CompactFlash data bidirectional bus.
15
35,36
33
I_C_33_5_N_
I_C_33_5_N_
I_C_33_5_N_
REG#
CE[2:1]#
OE#
Register select and I/O enable.
Active-low card enable.
Active-low output enable used to gate memory read data (attribute
memory). Host must negate the OE# signal during write operations.
Active-low write enable used for strobing memory write data (attribute
memory).
26
I_C_33_5_N_
WE#
32
30
7
I_C_33_5_N_
I_C_33_5_N_
O_T_33_1
IORD#
IOWR#
WP
Active-low I/O read enable.
Active-low I/O write enable.
Write protect (in memory-only mode).
IOIS16#
RESET
Data is 16-bit (in I/O & memory mode).
PC Card/CompactFlash reset.
Note : This pin requires an external reset pulse generator (RC network)
to allow for the startup time for the internal oscillator and PLL.
Device ready (in memory-only mode).
19
24
I_C_33_5_S_
O_T_33_2
READY
IREQ#
Active-low Interrupt request (in I/O & memory mode). Indicates to the
host system that the PC Card/CF requires host software service. Note:
interrupt can support level or pulsed types.
12
O_T_33_2
BVD1
Battery voltage detect 1 (in memory-only mode). Not supported so held
static.
STSCHG#
Active-low status-changed pin (in memory & I/O mode). Used to alert the
host system that the card status has changed. In this case it means that
a function’s ready state has changed. The host should check this by
considering each function’s PRR.
5,28,47
P_33
PCMCIA_VDD3V3 Connected internally.
UART (MODEM) FunctionNote3
58
O_T_33_1
SOUT
UART serial data output.
IrDA_Out
SIN
UART IrDA data output when MCR[6] is set in enhanced mode.
UART serial data input.
53
I_C_33_5_N_
IrDA_In
DCD#
DTR#
UART IrDA data input when IrDA mode is enabled (see above).
Active-low modem data-carrier-detect input.
Active-low modem data-terminal-ready output. If automated DTR# flow
control is enabled, the DTR# pin is asserted & deasserted if the receiver
FIFO reaches or falls below the programmed thresholds.
56
60
I_C_33_5_N_
O_T_33_1
485_En
RTS#
In RS485 half-duplex mode, the DTR# pin may be programmed to reflect
the state of the transmitter empty bit to control the direction of the RS485
transceiver buffer automatically (see register ACR[4:3]).
59
54
O_T_33_1
Active–low modem request-to-send output. If automated RTS# flow
control is enabled, the RTS# pin is de-asserted & reasserted when the
receiver FIFO reaches or falls below the programmed thresholds.
Active-low modem clear-to-send input. If automated CTS# flow control is
enabled, upon de-assertion of the CTS# pin the transmitter completes
the current character & enters idle mode until the CTS# pin is
reasserted. Note: flow control characters are transmitted regardless of
the state of the CTS# pin.
I_C_33_5_N_
CTS#
OV-0004 May 06
External—Free Release
Page 5 of 11
OXFORD [ OXFORD SEMICONDUCTOR ]
