Product Bulletin OP604ESA
September 1996
High Reliability NPN Silicon Phototransistor
Type OP604ESA-XN
(3)
Features
•
Processed to Optek’ Space level
s
screening program patterned after
FSA/SCC Generic Specification 5000
•
Miniature hermetically sealed package
•
Ideal for direct mounting in PC boards
•
Mechanically and spectrally matched
to the OP224 Series LED
Description
The OP604ESA consists of a high
reliability NPN silicon phototransistor
mounted in a miniature glass lensed,
hermetically sealed, “
pill”package.
All devices are processed to Optek’
s
program patterned after ESA/SCC
Generic Specification No. 5000. See
page 13-4 for details. This device type is
lensed and has an acceptance half angle
of 18
o
measured from the optical axis to
the half power point. The series is also
mechanically and spectrally matched to
Optek’ OP224 series high reliability
s
infrared emitting diode.
Absolute Maximum Ratings
(T
A
= 25
o
C unless otherwise noted)
Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 C to +150 C
o
o
Operating Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . -55 C to +125 C
Collector-Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 V
Emitter-Collector Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0 V
o (1)
Soldering Temperature (for 5 seconds with soldering iron) . . . . . . . . . . . . . 240 C
(2)
Power Dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mW
Notes:
(1) No-clean or low solids RMA flux is recommended. Duration can be extended to 10 seconds
maximum when wave soldering.
(2) Derate linearly 0.5 mW/
o
C above 25
o
C.
(3) “ defines the testing level per ESA/SCC Generic Specification 5000, Chart III. “ will be
X”
X”
either “ (full processing) or “ (reduced processing).
B”
C”
“ defines lot acceptance testing. “ will be either 1, 2, or 3. Level 3 is the lowest defined
N”
N”
level with emphasis on electrical tests, solderability, and visual inspection. Level 2 requires
all tests of Level 3 and adds indurance testing (burn-in) with drift limits on key parameters.
Level 1 is the most stringent LAT level and includes all requirements of Levels 2 and 3 plus
additional testing for tolerance of thermal, mechanical, and environmental exposure.
o
o
Part Number Guide
OP604ESA-XN
Optek
High Reliability
ESA/SCC Specification
No. 5000
“ - Full Processing
B”
“ - Reduced Processing
C”
Level ”
1”
Environmental/Mechanical
plus 2 & 3
Level “ Life Testing plus
2”
Level 3
Level “ Electrical
3"
Inspection
Optek Technology, Inc.
1215 W. Crosby Road
Carrollton, Texas 75006
13-32
(972) 323-2200
Fax (972) 323-2396
OPTEK [ OPTEK TECHNOLOGIES ]
