Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions
Storage Temperature (TSTG
Maximum Junction Temperature (TJ)
EE Pin Potential to Ground Pin
)
−65°C to +150°C
+150°C
Case Temperature (TC)
Commercial
V
−7.0V to +0.5V
−0.5V to +6.0V
VEE to +0.5V
0°C to +85°C
−40°C to +85°C
−5.7V to −4.2V
VTTL Pin Potential to Ground Pin
Input Voltage (DC)
Industrial
Supply Voltage (VEE
)
Voltage Applied to Output
in HIGH State (with VCC = 0V)
Current Applied to Output
in LOW State (Max)
−0.5V to VCC
Note 1: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
twice the rated IOL (mA)
ESD (Note 2)
≥2000V
Note 2: ESD testing conforms to MIL-STD-883, Method 3015.
Commercial Version
DC Electrical Characteristics
VEE = −4.2V to −5.7V, VCC = GND, VTTL = +4.5V to 5.5V, TC = 0°C to +85°C (Note 3)
Symbol
Parameter
Output Reference Voltage
Single-Ended Input
HIGH Voltage
Min
Typ
Max
Units
Conditions
VBB
VIH
−1380
−1320
−1260
mV
I
VBB = −2.1 mA
Guaranteed HIGH Signal for All Inputs
(with One Input Tied to VBB
Guaranteed LOW Signal for All Inputs
(with One Input Tied to VBB
−1165
−870
mV
mV
)
VIL
Single-Ended Input
LOW Voltage
−1830
−1475
)
VOH
VOL
VDIFF
VCM
IIH
Output HIGH Voltage
Output LOW Voltage
Input Voltage Differential
Common Mode Voltage
Input HIGH Current
2.5
V
V
I
I
OH = −2.0 mA
OL = 20 mA
V
IN = VIH (Max)
0.5
or VIL (Min)
150
mV
V
Required for Full Output Swing
V
CC − 2.0
V
CC − 0.5
350
µA
V
IN = VIH (Max), D0–D5 = VBB
,
D0–D5 = VIL (Min)
IIL
Input LOW Current
0.5
−150
−37
µA
mA
mA
mA
V
V
IN = VIL (Min), D0–D5 = VBB
OUT = GND (Note 4)
IOS
IEE
ITTL
Output Short-Circuit Current
VEE Power Supply Current
VTTL Power Supply Current
−60
−17
65
−27
D0–D5 = VBB
D0–D5 = VBB
45
Note 3: The specified limits represent the “worst case” value for the parameter. Since these values normally occur at the temperature extremes, additional
noise immunity and guardbanding can be achieved by decreasing the allowable system operating ranges. Conditions for testing shown in the tables are cho-
sen to guarantee operation under “worst case” conditions.
Note 4: Test one output at a time.
DIP AC Electrical Characteristics
VEE = −4.2V to −5.7V, VCC = GND, VTTL = +4.5V to +5.5V
T
C = 0°C
T
C = +25°C
TC = +85°C
Symbol
Parameter
Units
ns
Conditions
Min
Max
Min
Max
Min
Max
tPLH
tPHL
tPLH
tPHL
Propagation Delay
Data to Output
C
L = 15 pF
Figures 1, 2
CL = 50 pF
0.80
1.60
3.50
4.30
0.90
3.70
1.00
4.00
Propagation Delay
Data to Output
1.70
4.50
1.80
4.80
ns
Figures 1, 3
3
www.fairchildsemi.com
ONSEMI [ ONSEMI ]
