.
IBM16M64644HGA IBM16M32644HGA
IBM16M64734HGA IBM16M32734HGA
Preliminary
Features
32/64Mx64/72 1 or 2 Bank Registered DDR SDRAM Module
• 184-Pin Registered 8-Byte Dual In-Line Memory
Module
• 32M/64Mx72 and x64 Double Data Rate (DDR)
SDRAM DIMM (32M X 8 SDRAMS)
• Performance:
• Bi-directional data strobe with one clock cycle
preamble and one-half clock post-amble
• Differential clock inputs
• Data is read or written on both clock edges
• Address and control signals are fully synchro-
nous to positive clock edge
PC200
3.5
100 125 125 133 MHz
10 8.0 8.0 7.5 ns
PC266B Units
DIMM CAS Latency
Clock Frequency
Clock Cycle
3
3
3.5
• Programmable Operation:
f
t
f
- DIMM CAS Latency: 3, 3.5
- Burst Type: Sequential or Interleave
- Burst Length: 2, 4, 8
CK
CK
DQ
DQ Burst Frequency 200 250 250 266 MHz
- Operation: Burst Read and Write
• Auto Refresh (CBR) and Self Refresh Modes
• Automatic and controlled precharge commands
• Power Down Mode
• 13/10/2 Addressing (row/column/bank)
• 7.8 µs Max. Average Periodic Refresh Interval
• Card size: 5.25" x 0.157" x 1.70"
• Gold contacts
• Intended for 100MHz and 133MHz applications
• Inputs and outputs are SSTL-2 compatible
• V = 2.5Volt ± 0.2, V
= 2.5Volt ± 0.2
DD
DDQ
• Single Pulsed RAS interface
• SDRAMs have four internal banks for concur-
rent operation
• Module has one or two physical banks depend-
ing on configuration
• SDRAMS in 66-pin TSOP-II Package
• Serial Presence Detect
Description
This Registered 184-Pin Double Data Rate (DDR)
Synchronous DRAM Dual In-Line Memory Module
(DIMM) can be organized as both a one- and two-
bank high-speed memory array. The 32Mx64/72 is
a single-bank DIMM that uses nine (x72) or eight
(x64) 32Mx8 DDR SDRAMs in 400 mil TSOP pack-
ages. The 64Mx64/72 is a two-bank DIMM that uses
18 (x72) or 16 (x64) 32Mx8 SDRAMs in 400 mil
TSOP packages. The DIMM achieves high-speed
data transfer rates of up to 266MHz.
(CKE0 and/or CKE1) control all devices on the
DIMM.
Prior to any access operation, the device CAS
latency and burst type/length/operation type must
be programmed into the DIMM by address inputs
A0-A12 using the mode register set cycle. The
DIMM CAS latency exceeds the SDRAM device
spec by one clock due to the address and control
signals being clocked to the SDRAM devices.
These DIMMs are manufactured using raw cards
developed for broad industry use by IBM as ’refer-
ence designs’. The use of these common design
files will minimize electrical variation between sup-
pliers.
The DIMM is intended for use in applications oper-
ating from 100MHz to 133MHz clock speeds with
data rates of 200 to 266 MHz. All control and
address signals are re-driven through registers to
the DDR SDRAM devices. The control and address
input signals are latched in the register on one rising
clock edge and sent to the SDRAM devices on the
following rising clock edge.
The DIMM uses serial presence detects imple-
mented via a serial EEPROM using the two-pin IIC
protocol. The first 128 bytes of serial PD data are
programmed and locked during module assembly.
The last 128 bytes are available to the customer.
A phase-locked loop (PLL) on the DIMM is used to
re-drive the differential clock signals to both the
DDR SDRAM devices and the registers, thus mini-
mizing system clock loading. Clock enable(s)
All IBM 184 DDR SDRAM DIMMs provide a high-
performance, flexible 8-byte interface in a 5.25” long
space-saving footprint.
©IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
19L7358.H02502
3/00
Page 1 of 28
IBM [ IBM ]
