EliteMT
M11B416256A
Notes :
back to VIH ) is indeterminate. OE held high and
WE taken low after CAS goes low result in a LATE
WRITE ( OE -controlled) cycle.
1. Enables on-chip refresh and address counters.
2. VIH(min) and VIL(max) are reference levels for
measuring timing of input signals. Transition times
are measured between VIH and VIL.
3. In addition to meet the transition rate specification,
all input signals must transit between VIH and VIL in a
monotonic manner.
12. Those parameters are referenced to CAS leading
edge in EARLY WRITE cycles and WE leading edge
in LATE WRITE or READ-MODIFY- WRITE cycles.
13. During a READ cycle, if OE is low then taken HIGH
before CAS goes high, I/O goes open, if OE is tied
4. Assume that tRCD < tRCD(max). If tRCD is greater than
the maximum recommended value shown in this
table, tRAC will increase by the amount that tRCD
exceeds the value shown.
permanently
low,
a
LATE
WRITE
or
READ-MODIFY-WRITE operation is not possible.
5. Assume that tRCD ≥ tRCD (max)
14. An initial pause of 200µs is required after power-up
6. If CAS is low at the falling edge of RAS , data-out
followed by eight RAS refresh cycles (RAS only or
CBR) before proper device operation is assured. The
eight RAS cycle wake-ups should be repeated any
time the tREF refresh requirement is exceeded.
will be maintained from the previous cycle. To initiate
a new cycle and clear the data-out buffer, CAS and
RAS must be pulsed high.
15. WRITE command is defined as WE going low.
7. Operation within the tRCD limit ensures that tRCD
(max) can be met, tRCD (max) is specified as a
reference point only ; if tRCD is greater than the
specified tRCD (max) limit, access time is controlled
by tCAC.
8. Operation within the tRAD limit ensures that tRAD(max)
can be met. tRAD(max) is specified as a reference
point only ; if tRAD is greater than the specified tRAD
(max) limit, access time is controlled by tAA.
16. LATE WRITE and READ-MODIFY-WRITE cycles must
have both tOFF2 and tOEH met ( OE high during
WRITE cycle) in order to ensure that the output
buffers will be open during the WRITE cycles.
17. The I/Os open during READ cycles once tOFF1 or tOFF2
occur.
18. Referenced to the earlier CAS falling edge.
19. Referenced to the latter CAS rising edge.
20. Output parameter (I/O) is referenced to corresponding
9. Either tRCH or tRRH must be satisfied for a READ
cycle.
CAS input, IO0~7 by CASL and IO8~15 by
CASH.
10. tOFF1(max) defines the time at which the output
achieves the open circuit condition ; it is not a
reference to VOH or VOL.
21. Last falling CAS edge to first rising CAS edge.
22. Last rising CAS edge to next cycle’s last rising
CAS edge.
23. Last rising CAS edge to first falling CAS edge.
24. Each CAS must meet minimum pulse width.
11. tWCS, tRWD, tAWD and tCWD are restrictive operating
parameters
in
LATE
WRITE
and
READ-MODIFY-WRITE cycle only. If tWCS
≥
tWCS(min) , the cycle is an EARLY WRITE cycle and
the data output will remain an open circuit throughout
the entire cycle. If tRWD ≥ tRWD(min) , tAWD ≥ tAWD(min)
and tCWD ≥ tCWD(min) , the cycle is READ-WRITE and
the data output will contain data read from the
selected cell. If neither of the above conditions is
25. Referenced to the latter CAS falling edge.
26. All IOs controlled by OE , regardless CASL and
CASH.
met, the state of I/O (at access time and until CAS
and RAS or OE go
Elite Memory Technology Inc
Publication Date : Feb. 2004
Revision : 1.9
6/15