General
Abs olute Maximum Ratings
Stress in excess of Absolute Maximum
Ratings may cause permanent damage.
Absolute Maximum Ratings, sometimes
referred to as no destruction limits, are
normally tested with one parameter at a
time exceeding the limits of Output data
or Electrical Characteristics. If exposed to
stress above these limits, function and
performance may degrade in an unspeci-
fied manner.
Characteris tics
min
–45
–55
–0.5
Unit
ma x
+100
+125
+40
TC
TS
Case temperature at full output power
Storage temperature
°C
°C
V
I
Continuous input voltage
Vdc
Isolation voltage
(input to output test voltage)
1,500
Vdc
V
ISO
V
tr
Transient input energy
0.01
Ws
VRC
–5
–5
Remote control voltage pin 10, 11 ref. to pin 18
Output adjust voltage pin 8, 9 ref. to pin 18
V
Vdc
Vdc
I
V
adj
+40
Input TC < TCmax unless otherwise specified
Characteris tics
Input voltage range1)
Conditions
min
typ
max
Unit
V
18
16
36
18
19
V
I
Turn-off input voltage
Turn-on input voltage
Input capacitance
See typical characteristics
See typical characteristics
16.8
18.3
2.4
V
V
Ioff
V
Ion
V
CI
PIi
ꢀF
NOTES:
1)
(V = 24V)
360
300
The power modules will operate down to
I
Input idling power
IO = 0, TC = –30…+ 85 °C
mW
mW
(V = 27V)
I
V ?18 V, when V decreases, but will turn on
I
I
at V ?19 V, when V increases (see also
I
I
TC = –30…+ 85 °C,
(V = 24V)
I
25
40
Operating Information.
PRC
Input stand-by power
RC connected to pin 18 (V = 27V)
I
2)
The test is applicable for through-hole
versions.
Environmental Characteris tics
Characteris tics
Tes t procedure & conditions
Frequency
Amplitude
10…500 Hz
0.75 mm
Vibration
(Sinusoidal)
JESD 22-B103
(IEC 68-2-6 Fc)
Acceleration
Number of cycles
10 g
10 in each axis
Frequency
Acceleration density
spectrum
10…500 Hz
0.5 g2/Hz
MIL-STD-883
Method 2026
(IEC 68-2-34 Ed)
Random
vibration
Duration
Reproducability
10 min in 3 directions
medium (IEC 62-2-36)
Shock
(Half sinus)
Peak acceleration
Shock duration
200 g
3 ms
JESD 22-B104
(IEC 68-2-27 Ea)
Temperature
Number of cycles
–40°C…+125°C
500
Temperature
change
JESD 22-A104
(IEC 68-2-14 Na)
JESD 22-A101
(IEC 68-2-3 Ca
with bias)
Temperature
Humidity
Duration
85°C
85% RH
1000 hours
Accelerated
damp heat
Solder
resistability2)
JESD 22-B106
(IEC 68-2-20 Tb 1A)
Temperature, solder
Duration
260°C
10…13 s
Duration
Temperature
Concentration
96 h
35°C
5 %
Aggressive
environment
IEC 68-2-11 Ka
2
EN/LZT 146 31 R1B © Ericsson Power Modules AB, March 2004
ERICSSON [ ERICSSON ]
