PBL 3771/1
The current-decay rate during the
turn-off portion of the switching cycle,
can be selected fast or slow by the CD
input.
Applications Information
Functional Description
Each channel of the PBL 3771/1
consists of the following sections: an
H-bridge output stage, capable of driving
up to 650 mA continuous motor current
(or 500 mA, both channels driven), a
logic section that controls the output
transistors, an S-R flip-flop, and two
comparators. The oscillator is common
to both channels.
Constant current control is achieved
by switching the current to the windings.
This is done by sensing the (peak)
voltage across a current-sensing
resistor, RS, effectively connected in
series with the motor winding, and
feeding that voltage back to a
comparator. When the motor current
reaches a threshold level, determined by
the voltage at the reference input, VR,
the comparator resets the flip-flop, which
turns off the output transistors. The
current decreases until the clock
oscillator triggers the flip-flop, which
turns on the output transistors again,
and the cycle is repeated.
Current control
The output current to the motor winding
is mainly determined by the voltage at
the reference input and the value of the
sensing resistor, RS.
In slow current-decay mode, only one
of the lower transistors in the H-bridge
(those closest to the negative supply) is
switched on and off, while one of the
upper transistors is held constantly on.
During turn-off, the current recirculates
through the upper transistor (which one
depends on current direction) and the
corresponding free-wheeling diode
connected to VMM, see figure 5.
Chopping frequency, winding
inductance, and supply voltage will affect
the current level, but to much less
extent. Fast current decay setting will
produce somewhat lower (average)
current than slow current decay. The
peak current through the sensing
resistor (and motor winding) can be
expressed as:
In fast current decay mode, both the
upper and lower transistors are
switched. During the off-time, the
freewheeling current is opposed by the
supply voltage, causing a rapid dis-
charge of energy in the winding.
Fast current decay may be required in
half- and microstepping applications
when rapid changes of motor current are
necessary. Slow current decay,
however, gives less current ripple, and
should always be selected, if possible, to
mini-mize core losses and switching
noise.
IM,peak = 0.18 • (VR / RS)
[A]
i.e., with a recommended value of 1 ohm
for the sensing resistor, RS, a 2.5 V
reference voltage will produce an output
current of approximately 450 mA. To
improve noise immunity on the VR input,
the control range may be increased to
5 volts if RS is correspondingly changed
to 2 ohms.
V
V
(+5 V)
CC
2
1
MM
+
0.1 mF
0.1 mF
4
10 mF
11
3
20
V
V
V
CC
MM1
MM2
M
M
M
7
A1
Phase
1
8
9
CD
1
1
B1
A2
B2
V
R1
3
PBL 3771/1
19
16
Phase
2
15
14
CD
2
R
22
s
M
V
R2
GND
C
E
C
E
2
RC
12
15 kW
STEPPER
MOTOR
2
1
1
2
21
13
5, 6,
17, 18
10
Motor Current
1 kW
1 kW
+5 V
Pin numbers refer
to DIL package.
820 pF
1.0 W
820 pF
3 300 pF
1.0 W
R
R
S
S
GND
(V
2
3
1
)
GND (V
)
MM
CC
Time
FAST Current Decay
SLOW Current Decay
Figure 5. Output stage with current paths
during turn -on, turn-off and phase shift.
Figure 6. Typical stepper motor application with PBL 3771/1.
5
ERICSSON [ ERICSSON ]
