PBL 3766
Ref.
Fig.
Parameter
Conditions
Min
Typ
Max
Unit
Digital inputs (C1, C2, E0)
Input low voltage, VIL
Input high voltage, VIH
Input low current, IIL
C1, C2
0
2.0
0.8
VCC
V
V
VIL = 0.4 V
VIH = 2.4 V
-200
-100
µA
µA
µA
E0
Input high current, IIH
40
0.6
20
Digital output (DET)
Output low voltage, VOL
Output high voltage, VOH
Internal pull-up resistor
DET short circuit current, IODs
IOL = 2 mA, E0 = 0
IOH = -100 µA, E0 = 0
0.4
V
V
kohm
µA
2.7
10
15
-330
E0 = 1, DET shorted to ground
Power supply rejection ratio, PSRR
To two-wire or four-wire port, from
VCC, PSRRCC
Note 12
50 Hz ≤ f ≤ 4 kHz
4 kHz ≤ f ≤ 50 kHz
50 Hz ≤ f ≤ 4 kHz
4 kHz ≤ f ≤ 50 kHz
50 Hz ≤ f ≤ 4 kHz
4 kHz ≤ f ≤ 50 kHz
30
30
30
12
40
30
35
35
35
18
50
35
dB
dB
dB
dB
dB
dB
VEE, PSRREE
VBat, PSRRBat
Power supply currents (relay driver off)
VCC current, ICC
VEE current, IEE
VBat current, IBat
VCC current, ICC
VEE current, IEE
VBat current, IBat
VCC current, ICC
VEE current, IEE
VBat current, IBat
Open circuit state
C2, C1 = 0, 0
On-hook
Stand-by state
C2, C1 = 1, 1
On-hook
Active state
C2, C1 = 1, 0
On-hook
1
1
0.5
2
1
0.5
4
2
mA
mA
mA
mA
mA
mA
mA
mA
mA
3
Power dissipation
Open circuit state total dissipation, POp
C2, C1 = 0, 0
On-hook (RL = ∞) or off-hook (RL = 0)
C2, C1 = 1, 1
On-hook (RL = ∞)
C2, C1 = 1, 0
25
35
mW
mW
mW
Stand-by state total dissipation, POnSb
Active state total dissipation, POnAct
35
45
160
220
On-hook (RL = ∞)
Active state total dissipation,
C2, C1 = 1, 0, Note 13
Off-hook, RL = 200 ohm
Off-hook, RL = 600 ohm
POffAct200
POffAct600
1.35
1.05
1.50
1.20
W
W
Temperature guard
Junction temperature at threshold, TJG
Temperature guard hysteresis, ∂TJG
145
160
20
170
°C
°C
Thermal resistance
28-pin PLCC, θJP28plcc
Junction to terminals 3, 6, 10, 17, 24
connected together, Note 14
Junction to terminals 5, 6, 17, 18
connected together, Note 14
10
10
15
15
°C/W
°C/W
22-pin plastic DIP, θJP22dip
4-6