欢迎访问ic37.com |
会员登录 免费注册
发布采购

EM83812BP 参数 Datasheet PDF下载

EM83812BP图片预览
型号: EM83812BP
PDF下载: 下载PDF文件 查看货源
内容描述: ALL-倾朝野PLUG &PLAY SCRLLING的串行鼠标控制器 [ALL-INONE PLUG & PLAY SCRLLING SERIAL MOUSE CONTROLLER]
分类和应用: 控制器局域网
文件页数/大小: 11 页 / 88 K
品牌: ELAN [ ELAN MICROELECTRONICS CORP ]
 浏览型号EM83812BP的Datasheet PDF文件第1页浏览型号EM83812BP的Datasheet PDF文件第3页浏览型号EM83812BP的Datasheet PDF文件第4页浏览型号EM83812BP的Datasheet PDF文件第5页浏览型号EM83812BP的Datasheet PDF文件第6页浏览型号EM83812BP的Datasheet PDF文件第7页浏览型号EM83812BP的Datasheet PDF文件第8页浏览型号EM83812BP的Datasheet PDF文件第9页  
EM83812  
ALL-INONE PLUG & PLAY SCRLLING SERIAL MOUSE CONTROLLER  
FUNCTIONAL BLOCK DIAGRAM  
THREE TYPES SELECTOR  
RXD  
Z1  
Z2  
VOLTAGE  
SENSOR  
KEY-SWITCH  
DETECTOR  
COMPARATOR  
RTS  
Z-AXIS COUNTER  
C
O
M
P
A
R
A
T
O
R
OPT  
X1  
D
E
T
E
C
T
O
R
M
O
T
I
O
N
DATA  
I/O  
COUNTER  
MULTIPLEXER  
X2  
Y1  
Y2  
D
E
B
O
U
N
C
E
L
M
COMMAND  
STATUS  
TIMING  
CONTROLLER  
R
SYSTEM CLOCK  
GENERATOR  
OSCR  
OSC.OUT  
RC  
OSCILLATION  
PIN DESCRIPTIONS  
Symbol  
I/O  
Function  
INPUT: 200kohm pull low to VSS.  
OPT  
I/O  
When OPT is connected to VDD, EM84520 will enter test mode. In test mode,  
L will be the output of X1,while M will be the output of X2. Toggling R key can  
change these output to be Y1,Y2 or Z1,Z2 respectively.  
OUTPUT: 2kHz Z-axis LED driving source with A/D/E/F version.  
"1"= VDD, "0"= floating  
High duty is about 60us.  
OSC.OUT  
O
The RC oscillation clock output. Or 3mA sink current output for X, Y photo  
emitters.  
OSCR  
RTS  
I
I/O  
Connect 50kΩ±1% precise resistor for oscillation.  
±12V signal with 10mA driving. Used as PnP ID code output trigger signal  
from 10w (-12V) to high (+12V) while under normal operating. RTS will keep on  
±12V driving.  
RXD  
I/O  
One report contains 4 data bytes, 7 data bits without parity in the data byte.  
The data byte is sgifted out from LSB through MSB, started by start bit and ended  
by stop bit. The RXD signal swing between +6V and -6V.  
Three key-switches inputs. 200kresistor pull low.  
In Z-axis key mode, M key toggling can change the scrolling speed from low to  
high.  
R
M
L
I
I/O  
I/O  
X1  
X2  
Y1  
Y2  
Z1  
Z2  
I
I
I
I
I
I
Three step dynamic input impedance. If OSC.OUT is not connected to LEDs, the  
dynamic input impedance will be off.  
Use current comparator to measure photo-couples "ON", or "OFF".  
Z-axis input.  
Photo mode : Three steps dynamic input impedance. Current comparator input.  
Key mode : 200 kresistor pull low. 7 levels increased by "M" key.  
Voltage mode : 200 kresistor pull low. 7 levels voltage comparator.  
Mechanical mode : 13.2kresistor pull low. Current comparator input.  
Negative power.  
VSS  
VDD  
Power line.  
9.3.1999  
* This specification are subject to be changed without notice.  
2