SNAP Analog Input Modules
Current Input Module, -20 mA to +20 mA, 32 Channels
transmitters on different modules or use different power
supplies. (If you need channels that are isolated from each
other on the same module, see Opto 22 form #1182.)
Specifications
Input Range
-20 mA to +20 mA
From -22 to +22 mA
(+/-20 mA range)
Over-Range Limits
Part Number
Description
Resolution
0.8 microamps
-3 dB @ 31 Hz
1.15 s
SNAP-AIMA-32
32-channel analog current input,
-20 mA to +20 mA
Input Filtering
SNAP-AIMA-32-FM
Data Freshness (Max)
Wiring harness for SNAP-AIMA-32
modules and breakout racks
SNAP-HD-BF6
DC Common Mode Rejection >-120 dB
SNAP-AIMA-HDB
SNAP-AIMA-HDB-FM and SNAP-AIMA-32-FM
Breakout racks for SNAP-AIMA-32
AC Common Mode Rejection >-120 dB @ 60 Hz
Maximum Survivable Input
36 mA or 9 VDC
250 V
Maximum Operating Common
Mode Voltage
Wiring
SNAP TEX cables and a breakout rack are available separately
for wiring points to field devices (see form #1756, the SNAP
TEX Cables & Breakout Boards Data Sheet). The SNAP-HD-BF6
cable connects the module to the breakout rack, which can
then be wired to field devices. (NOTE: The SNAP-HD-CBF6
wiring harness with flying leads is not recommended for this
module.)
Accuracy
0.1% (20 microamps)
30 PPM/ °C
DRIFT: Gain Temperature
Coefficient
DRIFT: Offset Temperature
Coefficient
15 PPM/ °C
Isolation
1500 V, field to logic
Power Requirements
5 VDC (±0.15 ) @ 150 mA
CAUTION: We strongly recommend that you use the breakout
rack with these modules. Miswiring of any point on the
module can cause severe out-of-warranty damage. The
breakout rack protects the module from many wiring errors.
Input Resistance - Single
Ended
100 ohms (each channel)
Operating Temperature
Storage Temperature
0 °C to 70 °C
-40 °C to 85 °C
4 in-lb (0.45 N-m)
5.26 in-lb (0.6 N-m)
if you are using the module with loop power (2-wire) negative
common devices, connect to the SNAP-AIMA-HDB (or -FM)
rack. If you are using the module with self-powered devices
(4-wire) or with devices that share a common positive
connection, do not use the SNAP-AIMA-HDB (or -FM) boards,
which have a current limiting diode. Instead, wire to the SNAP-
AIV-HDB or SNAP-AIV-HDB-FM.
Torque, hold-down screws
Torque, connector screws
SNAP-AIMA-32: UL, CE,
RoHS, DFARS.
SNAP-AIMA-32-FM: CE, FM,
RoHS, DFARS
Agency Approvals
Warranty
Lifetime
Correcting for Inverted Scaling
Description
Positive readings for these modules appear as negative values.
Therefore, in order to obtain meaningful readings, use the
scaling feature in PAC Control as follows:
1. In the Add or Edit Analog Point dialog box for each point,
choose the scalable version of the module.
2. Under Scaling, scale each point negatively as shown
The SNAP-AIMA-32 and SNAP-
AIMA-32-FM modules provide 32
channels of input with an input
range of
-20mA to +20mA. The SNAP-AIMA-
32-FM is Factory Mutual approved.
Check the table on page 3 for I/O
processor compatibility.
below:
Dimensional drawings are on page 39.
These modules DO NOT supply loop excitation current.
Channels are not isolated from each other. Since all inputs
share a common reference, the module must be installed at
the beginning or end of a typical 4–20 mA loop. If you use
both standard and self-sourcing transmitters, put the
Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com
PAGE
9
SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com
© 2001–2014 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
E-OEC [ OPTO ELECTRONICS CO,. LTD ]
