欢迎访问ic37.com |
会员登录 免费注册
发布采购

AM29LV008B-100FE 参数 Datasheet PDF下载

AM29LV008B-100FE图片预览
型号: AM29LV008B-100FE
PDF下载: 下载PDF文件 查看货源
内容描述: [Flash Memory,]
分类和应用:
文件页数/大小: 39 页 / 142 K
品牌: CYPRESS [ CYPRESS ]
 浏览型号AM29LV008B-100FE的Datasheet PDF文件第5页浏览型号AM29LV008B-100FE的Datasheet PDF文件第6页浏览型号AM29LV008B-100FE的Datasheet PDF文件第7页浏览型号AM29LV008B-100FE的Datasheet PDF文件第8页浏览型号AM29LV008B-100FE的Datasheet PDF文件第10页浏览型号AM29LV008B-100FE的Datasheet PDF文件第11页浏览型号AM29LV008B-100FE的Datasheet PDF文件第12页浏览型号AM29LV008B-100FE的Datasheet PDF文件第13页  
P R E L I M I N A R Y  
Am29LV008 is erased or programmed in a system with-  
Autoselect  
out access to high voltage on the A9 pin.The command  
sequence is illustrated in Table 5 on page 13.  
The Autoselect mode allows the reading out of a binary  
code from the device and will identify its manufacturer  
and type.The intent is to allow programming equipment  
to automatically match the device to be programmed  
with its corresponding programming algorithm.The Au-  
toselect command may also be used to check the sta-  
tus of write-protected sectors (see Table 2). This mode  
is functional over the entire temperature range of the  
device.  
Byte 0 (A0 = V ) represents the manufacturer’s code  
IL  
and byte 1 (A0 = V ) the device identifier code. For the  
IH  
Am29LV008 these two bytes are given in Table 2. All  
identifiers for manufacturer and device will exhibit odd  
parity with DQ7 defined as the parity bit. In order to  
read the proper device codes when executing Autose-  
lect, A1 must be V (see Table 2). The device code is  
IL  
3EH (for top boot block) or 37H (for bottom boot block).  
To activate this mode, the programming equipment  
must force V (12.0 V ± 5%) on address pin A9. Two  
In order to determine which sectors are write protected,  
ID  
identifier bytes may then be sequenced from the device  
A1 must be at V while running through the sector ad-  
IH  
outputs by toggling address A0 from V to V . All ad-  
dresses are don’t cares except A0, A1, and A6 see  
Table 2.  
dresses; if the selected sector is protected, a logical ‘1’  
will be output on DQ0 (DQ0 = 1).  
IL  
IH  
The manufacturer and device codes may also be read  
via the command register, for instances when the  
Table 2. Autoselect/Sector Protection Codes  
Code DQ DQ DQ DQ DQ DQ DQ DQ  
Type  
A13–A19  
A6  
A1  
A0  
(HEX)  
7
6
5
4
3
2
1
0
Manufacturer Code: AMD  
X
L
L
L
01H  
3EH  
0
0
0
0
0
0
0
1
29LV008 Device  
(Top Boot Block)  
X
X
L
L
L
L
L
H
H
L
0
0
0
0
0
0
1
1
0
1
1
0
1
0
0
1
1
0
1
1
0
0
1
1
29LV008 Device  
(Bottom Boot Block)  
37H  
Set Sector  
Addresses  
Sector Protection  
H
01H*  
X = Don’t care.  
* Outputs 01H at protected sector addresses.  
Am29LV008T/Am29LV008B  
9