欢迎访问ic37.com |
会员登录 免费注册
发布采购

C430CB230-S0100 参数 Datasheet PDF下载

C430CB230-S0100图片预览
型号: C430CB230-S0100
PDF下载: 下载PDF文件 查看货源
内容描述: SuperBlue ™ LED灯 [SuperBlue⑩ LEDs]
分类和应用:
文件页数/大小: 2 页 / 122 K
品牌: CREE [ CREE, INC ]
 浏览型号C430CB230-S0100的Datasheet PDF文件第1页  
Maximum Ratings at TA = 25°CNotes ꢀ&3  
DC Forward Current  
C430CB230-S0ꢀ00  
15 mA  
Peak Forward Current (1/10 duty cycle @ 1kHz)  
LED Junction Temperature  
35 mA  
125°C  
Reverse Voltage  
5 V  
Operating Temperature Range  
-40°C to +100°C  
-40°C to +100°C  
1000 V  
Storage Temperature Range  
Electrostatic Discharge Threshold (HBM)Note 2  
Electrostatic Discharge Classification (MIL-STD-883E)Note 2  
Class 2  
Note 3  
Typical Electrical/Optical Characteristics at TA = 25°C, If = ꢀ0 mA  
Forward  
Voltage  
(Vf, V)  
Reverse  
Current  
[I(Vr=5V), μA]  
Peak  
Wavelength  
(λd, nm)  
Dominant  
Full Width  
Half Max  
(λD, nm)  
Radiant Flux  
(P, μW)  
Flux  
(mlm)  
Part Number  
Wavelength  
(λd, nm)  
Typ.  
4.0  
Max.  
Min.  
Typ.  
Max.  
Typ.  
Typ.  
Min.  
462  
Typ.  
Max.  
466  
Typ.  
C430CB230-S0100  
4.5  
425  
650  
10  
40  
428  
465  
60  
Mechanical Specifications  
Description  
C430CB230-S0ꢀ00  
Dimension  
Tolerance  
± 25  
P-N Junction Area (μm)  
Top Area (μm)  
176 x 176  
200 x 200  
200 x 200  
250  
± 25  
Bottom Area (μm)  
± 25  
Chip Thickness (μm)  
± 25  
Au Bond Pad Diameter (μm)  
Au Bond Pad Thickness (μm)  
Back Contact Metal Area (μm)  
112  
± 20  
1.2  
± 0.5  
± 10  
20  
Notes:  
1. Maximum ratings are package dependent. The above ratings were determined using a T-1 3/4 package (with Hysol OS4000  
epoxy) for characterization. Ratings for other packages may differ. The forward currents (DC and Peak) are not limited by the die  
but by the effect of the LED junction temperature on the package. The junction temperature limit of 125°C is a limit of the T-1  
3/4 package; junction temperature should be characterized in a specific package to determine limitations. Assembly processing  
temperature must not exceed 325°C (<5 seconds).  
2. Product resistance to electrostatic discharge (ESD) according to the HBM is measured by simulating ESD using a rapid avalanche  
energy test (RAET). The RAET procedures are designed to approximate the maximum ESD ratings shown. The RAET procedure is  
performed on each die. The ESD classification of Class II is based on sample testing according to MIL-STD-883E.  
3. All products conform to the listed minimum and maximum specifications for electrical and optical characteristics, when assembled  
and operated at 10 mA within the maximum ratings shown above. Efficiency decreases at higher currents. Typical values given  
are within the range of average values expected by the manufacturer in large quantities and are provided for information only. All  
measurements were made using lamps in T-1 3/4 packages (with Hysol OS4000 epoxy). Optical characteristics measured in an  
integrating sphere using Illuminance A.  
4. Specifications are subject to change without notice.  
Cree, Inc.  
4600 Silicon Drive  
Copyright © 1999-2004 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree,  
the Cree logo and G•SiC are registered trademarks, and SuperBlue is a trademark of Cree, Inc.  
Durham, NC 27703  
USA Tel: +1.919.313.5300  
www.cree.com  
2
CPR3AB Rev. H  
 复制成功!