CPC7582
Absolute Maximum Ratings (@ 25˚ C)
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at these or
any other conditions beyond those indicated in the opera-
tional sections of this data sheet is not implied. Exposure of
the device to the absolute maximum ratings for an extend-
ed period may degrade the device and effect its reliability.
Parameter
Min Max Units
Operating Temperature Range
Storage Temperature Range
Relative Humidity Range
Pin Soldering Temperature
(t=10 s max)
-40
-40
5
+110
+150
95
˚C
˚C
%
˚C
-
+260
+5V Power Supply
Battery Supply
Logic Input Voltage
Logic Input to Switch Output Isolation
Switch Isolation (SW1, SW2, SW3, SW5, SW6)
Switch Isolation (SW4)
-
-
-
-
-
-
7
-85
7
330
330
480
V
V
V
V
V
V
Power Supply Specifications
Supply
Min
+4.5
-19
Typ
+5.0
-
Max
+5.5
-72
Unit
V
V
VDD
Electrical Characteristics TA = -40oC to +85oC
1
VBAT
1 VBAT is used only as a reference for internal protection circuitry.
If VBAT rises above -10V, the device will enter an all off state and will remain in the all off state
until the battery voltage drops below -15V.
(unless otherwise specified)
Minimum and maximum values are production testing
requirements. Typical values are characteristic of the
device and are the result of engineering evaluations.
Typical values are provided for information purposes
only and are not part of the testing requirements.
ESD Rating (HBM)
1000V
Table 1. Break Switch, SW1 and SW2
Parameters
Conditions
Symbol
Min
Typ
Max
Units
Off-state Leakage Current:
+25˚C
Vsw (differential)= -320V to Gnd
Vsw (differential)= -60V to +260V
Vsw (differential)= -330V to Gnd
Vsw (differential)= -60V to +270V
Vsw (differential)= -310V to Gnd
Vsw (differential)= -60V to +250V
Isw
Isw
Isw
-
-
-
0.1
0.3
0.1
1
1
1
µA
µA
µA
+85˚C
-40˚C
RDSON (SW1,SW2):
+25˚C
+85˚C
-40˚C
RDSON Match
TLINE= +/-10 mA, +/-40mA, TBAT= -2V
TLINE= +/-10 mA, +/-40mA, TBAT= -2V
TLINE= +/-10 mA, +/-40mA, TBAT= -2V
Per ON-resistance Test Condition of
SW1, SW2RON SW1-RONSW2
∆ V
∆ V
∆ V
-
-
-
-
14.5
20.5
10.5
0.15
-
28
-
Ω
Ω
Ω
Ω
Magnitude
0.8
dc Current Limit:
+25˚C
+85˚C
Vsw (on) = +/- 10V
Vsw (on) = +/- 10V
Vsw (on) = +/- 10V
Break switches in ON state, Ringing
access switches OFF, Apply +/- 1000V
at 10/1000ms pulse, Appropriate
secondary protection in place.
lsw
lsw
lsw
Isw
-
80
-
300
160
400
2.5
-
-
mA
mA
mA
A
-40˚C
425
-
Dynamic Current Limit:
(t=<0.5µs)
-
Rev. 1.0
2
www.clare.com
CLARE [ CLARE ]
